1076616 SEAL-LIP TYPE Caterpillar parts
350, 350 L, 375, 5080
Rating:
Alternative (cross code) number:
CA1076616
107-6616
1076616
CA1076616
107-6616
1076616
Weight: 0.25 pounds 0 kg.
EXCAVATOR, FRONT SHOVEL,
Number on catalog scheme:
17
For full view, you need register
Information:
System Operation Description:Digital outputs are used to convey on/off information from the generator set control for energizing loads. The loads include relays, solenoids, and indicator lamps. The digital output must not be connected directly to battery positive (B+).The digital output circuit fault code occurs when the digital output wiring is shorted to battery positive (B+).Test Step 1. CHECK FOR A SHORTED HARNESS.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the harness connector from the EMCP 3.
Disconnect the digital output from the device that the output is connected to.
At the harness connector for the EMCP 3, measure the resistance from the failed digital output contact to all other EMCP 3 harness contacts.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the harness on the wire that has a low resistance measurement. Repair: Repair the harness or replace the harness.STOPTest Step 2. CHECK THE DEVICE CONNECTED TO THE DIGITAL OUTPUT CIRCUIT WIRING FOR SHORT TO THE BATTERY+ CIRCUIT.
Use the following steps in order to prevent the engine from running while performing the procedure.
Press the emergency stop push button.
Turn the battery disconnect switch to the ON position.
At the digital output device, measure the DC voltage on the wire connected to the failed digital output.Expected Result:The voltage is at or near 0 VDC and not shorted to battery positive (B+). Results:
OK - The digital output device is not shorted to battery positive (B+). Proceed to Test Step 3.
NOT OK - The digital output device is shorted to battery positive (B+).Repair: Repair the digital output device or replace the digital output device.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the EMCP 3 connector and clean the contacts of the EMCP 3 connector.
Reconnect the harness connector.
Reset the generator set.
Operate the generator set.
Check the status of the diagnostic code.Expected Result:The diagnostic code is not active.Results:
OK - The diagnostic code is not active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor connection or a short at one of the connectors that was disconnected and reconnected. Resume normal operation.STOP
NOT OK - The code is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: A failed EMCP 3 is unlikely. Exit the procedure and perform the entire procedure again. If the cause of the failure is not found, replace the ECM. Refer to Testing and Adjusting, RENR7902, "Electronic Control Module (Generator Set) - Replace".STOP
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the harness connector from the EMCP 3.
Disconnect the digital output from the device that the output is connected to.
At the harness connector for the EMCP 3, measure the resistance from the failed digital output contact to all other EMCP 3 harness contacts.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the harness on the wire that has a low resistance measurement. Repair: Repair the harness or replace the harness.STOPTest Step 2. CHECK THE DEVICE CONNECTED TO THE DIGITAL OUTPUT CIRCUIT WIRING FOR SHORT TO THE BATTERY+ CIRCUIT.
Use the following steps in order to prevent the engine from running while performing the procedure.
Press the emergency stop push button.
Turn the battery disconnect switch to the ON position.
At the digital output device, measure the DC voltage on the wire connected to the failed digital output.Expected Result:The voltage is at or near 0 VDC and not shorted to battery positive (B+). Results:
OK - The digital output device is not shorted to battery positive (B+). Proceed to Test Step 3.
NOT OK - The digital output device is shorted to battery positive (B+).Repair: Repair the digital output device or replace the digital output device.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the EMCP 3 connector and clean the contacts of the EMCP 3 connector.
Reconnect the harness connector.
Reset the generator set.
Operate the generator set.
Check the status of the diagnostic code.Expected Result:The diagnostic code is not active.Results:
OK - The diagnostic code is not active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor connection or a short at one of the connectors that was disconnected and reconnected. Resume normal operation.STOP
NOT OK - The code is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: A failed EMCP 3 is unlikely. Exit the procedure and perform the entire procedure again. If the cause of the failure is not found, replace the ECM. Refer to Testing and Adjusting, RENR7902, "Electronic Control Module (Generator Set) - Replace".STOP
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
12E, 140G, 143H, 14E, 14G, 16, 160H, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 16H NA, 235, 235B, 235C, 245, 24H, 3208, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B L, 3406, 3406B, 3406C, 3408, ...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 216B, 216B3, 226B, 226B3, 235, 235B, 245, 247B, 247B3, 330, 3...
1090, 120H, 120H ES, 120H NA, 130G, 135H NA, 16, 205B, 211B, 215, 215B, 215D, 224B, 225, 227, 229, 229D, 231D, 235, 235C, 235D, 245, 245B, 245D, 3114, 3116, 3208, 320B FM LL, 322C, 3304, 3306, 3306B, ...
320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 446, 446B, 446D, 5080, 50...
2384C, 2484C, 308E, 308E CR, 308E SR, 308E2 CR, 312, 315D L, 318E L, 319D, 319D L, 319D LN, 320, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320N, 322 FM L, 322 LN, 322B L, 32...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 16, 160G, 215, 215B, 225, 225D, 231D, 235, 235C, 235D, 245, 245B, 245D, 24M, 3408, 350, 365B, 365B II, 365B L, 375, 375 L, 385B, 46, 5080, 5090B, 5110B, 5130, ...
12E, 140G, 16, 245, 245B, 245D, 24H, 3412, 3412C, 375, 375 L, 5110B, 578, 583H, 583K, 583R, 587R, 589, 594, 621, 621B, 621E, 621F, 621G, 623E, 623F, 623G, 627, 627E, 627F, 627G, 631C, 631D, 631E, 631G...
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 2384C, 2484C, 24M, 301.5, 301.6C, 302.5, 302.5C, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305...
308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LC...
303.5C, 303.5D, 303.5E, 303C CR, 304.5, 304D CR, 304E, 305.5, 306, 308E, 308E CR, 308E SR, 308E2 CR, 318B, 318C, 319D L, 319D LN, 320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E RR, 322, 322B, 322C,...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 315D L, 316E L, 318D L, 322, 322 FM L, 322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324...
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
1211593
SEAL-BUFFER
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365C, 385C, 385C FS, 5080, 5090B
1554040
SEAL-O-RING
320B, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 345B II, 345B L, 365B, 365B II, 375, 385B, 5080, 5090B, M325C MH
320B, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 345B II, 345B L, 365B, 365B II, 375, 385B, 5080, 5090B, M325C MH
320B, 320C, 322B LN, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN, 324E LN, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 329E L, 329E LN, 330B L, 330C, 330C L, 330D L, 330D LN, 330D MH, 336D L, ...
1554038
SEAL-O-RING
320B, 320C, 322B LN, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN, 324E LN, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 329E L, 329E LN, 330B L, 330C, 330C L, 330D L, 330D LN, 330D MH, 336D L, ...
320B, 320C, 322B LN, 322C, 323D L, 323D LN, 324D, 324D L, 324D LN, 324E LN, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 329E L, 329E LN, 330B L, 330C, 330C L, 330D L, 330D LN, 330D MH, 336D L, ...
330, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D...
350, 350 L, 365B, 375, 375 L, 5080, 5090B
8C9191
SEAL-U-CUP
350, 350 L, 365B, 375, 375 L, 5080, 5090B
350, 350 L, 365B, 375, 375 L, 5080, 5090B