AVSPARE.COM
parts catalog

SEAL-LIP TYPE 1135950 - Caterpillar


1135950 SEAL-LIP TYPE Caterpillar parts 312D2, 350, 350 L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
Rating:
86
Alternative (cross code) number:
CA1135950
113-5950
1135950
Caterpillar 1135950 SEAL-LIP TYPE
Weight: 0.25 pounds 0 kg.
Information:
AXIAL WIDTH  8  mm
BORE DIAMETER  180  mm
MATERIAL  Polyurethane - 90 Duro 
SEAL OD  180.2  mm
SHAFT OD  149.85  mm

Buy SEAL-LIP TYPE 1135950 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, MOBILE HYD POWER UNIT,

Cross Reference:

CATERPILLAR 1135950,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$23.11
 

15 Jun 2022
0.3[0.14] Pounds
US: TakePart
CTP Caterpillar Seal-Lip Type (1135950) Aftermarket
CTP
Number on catalog scheme: 2
  For full view, you need register

Compatible equipment models: 1135950:

FRONT SHOVEL  385C   5090B  
MOBILE HYD POWER UNIT  385C   385C L   Caterpillar

Information:


Do not disassemble the Variable Valve Actuator. There are no components of the Variable Valve Actuator that are serviceable. If the Variable Valve Actuator is disassembled, the warranty will be void.
Illustration 1 g01102463
(1) Adjustment screw (2) Adjustment screw locknut (3) Intake rocker arm (4) Actuator rod
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Loosen adjustment screw locknut (2) and back out adjustment screw (1) until actuator rod (4) is not in contact with intake rocker arm (3) .Note: During this procedure, ensure that the intake rocker arm is in full contact with the valve bridge.
Place the appropriate feeler gauge between the actuator rod and the intake rocker arm. Turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the actuator rod and the intake rocker arm. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge. Set the clearance to 0.50 0.08 mm (0.020 0.003 inch).
Tighten the adjustment screw locknut to 50 10 N m (37 7 lb ft).
Recheck the lash setting after the adjustment screw locknut has been torqued.
Make the lash setting on the following cylinders: 1, 2 and 4.
Remove the timing bolt from the flywheel. Turn the crankshaft clockwise by 360 degrees. This will position the No. 6 piston at the top center on the compression stroke. Install the timing bolt in the flywheel.
Repeat Step 6 for the following cylinders: 3, 5 and 6.
Remove the timing bolt from the flywheel.

Cat SIS web machinery list:

Caterpillar parts catalog
390F L Excavator HNG00001-UP (MACHINE) POWERED BY C18 Engine
MH3295 Material Handler PA900001-UP (MACHINE) POWERED BY C18 Engine
375 & 375 L Excavator Custom Attachments 6NK00001-UP (MACHINE) POWERED BY 3406 Engine
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine
390F OEM PT700001-UP (MACHINE) POWERED BY C18 Engine
350 EXCAVATOR WITH MATERIAL HANDLER 8KZ00282-UP (MACHINE)
350 EXCAVATOR WITH MATERIAL HANDLER 8KZ00279-00281 (MACHINE)
350 EXCAVATOR WITH MATERIAL HANDLER 9FL00780-UP (MACHINE)
350 EXCAVATOR - MATERIAL HANDLER 3ML00941-UP (MACHINE)
350 L Excavator Custom Attachments 9FL00001-UP (MACHINE)
375 & 375 L Excavators 1JM00001-UP (MACHINE) POWERED BY 3406 Engine
375 and 375 L Excavators 6NK00001-UP (MACHINE) POWERED BY 3406 Engine
385B & 385B L Excavators CLS00001-UP (MACHINE) POWERED BY 3456 Engine
5090B Excavator CLD00001-UP (MACHINE) POWERED BY 3456 Engine
385B & 385B L Excavators BKF00001-UP (MACHINE) POWERED BY 3456 Engine
385B Excavator ANS00001-UP (MACHINE) POWERED BY 3456 Engine
385B Excavator MYA00001-UP (MACHINE) POWERED BY 3456 Engine
5090B Excavator SJY00001-UP (MACHINE) POWERED BY 3456 Engine
385B L Excavator RCD00001-UP (MACHINE) POWERED BY 3456 Engine
385C L Excavator JCM00001-UP (MACHINE) POWERED BY C-18 Engine
385C Excavator KBC00001-UP (MACHINE) POWERED BY C18 Engine
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
385C L Excavator T2E00001-UP (MACHINE) POWERED BY C-18 Engine
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C18 Engine
385C Excavator MNZ00001-UP (MACHINE) POWERED BY C-18 Engine
385C FS Excavator T2F00001-UP (MACHINE) POWERED BY C18 Engine
385C FS Excavator GLT00001-UP (MACHINE) POWERED BY C18 Engine
385C & 385C L Excavator KGB00001-UP (MACHINE) POWERED BY C18 Engine
385C FS Excavator EAM00001-UP (MACHINE) POWERED BY C-18 Engine
385C Material Handler WAW00001-UP (MACHINE) POWERED BY C-18 Engine
390D L Excavator WAG00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WBT00001-UP (MACHINE) POWERED BY C18 Engine


Parts seal Caterpillar catalog:

2160009 SEAL-U-CUP
345C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 385B, 385C, 385C L, 390D, 390D L
1709851 SEAL-BUFFER
345C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L
1915646 SEAL-U-CUP
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
0965169 SEAL-BUFFER
350, 350 L, S25
1119957 SEAL-LIP TYPE
325B L, 330, 330 FM L, 330 L, 330B L, 350, 350 L, CR20, P16
3673929 SEAL-U-CUP
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
3673928 SEAL-BUFFER
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
3678471 SEAL-O-RING
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
2160010 SEAL-U-CUP
385B, 385C, 385C L, 390D, 390D L
3678472 SEAL-O-RING
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
9X4600 SEAL-LIP TYPE
312D2, 330B L, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L...
8C9182 SEAL AS
312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5130B, CR20, P16, S25
3673933 SEAL-U-CUP
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
0951732 SEAL-O-RING
312D2, 385B, 385C, 385C L, 390D, 390D L, 988K
1723918 SEAL AS
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 988K
3673932 SEAL-BUFFER
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
1659295 SEAL-LIP TYPE
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.