1174473 SEAL Caterpillar parts
307B, 5080, 795F AC, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, 986H, AD30, AD45B, AD55B, AD60, CB-434D, CB-534D, CB-564D, CTV40, CWAC-40, IT62G II, IT62H, M313C, M315C...
Rating:
Alternative (cross code) number:
CA1174473
117-4473
1174473
CA1174473
117-4473
1174473
Weight: 0.01 pounds 0 kg.
Information:
MATERIAL
Rubber
THICKNESS
5
mm
UNIT MEASURE
CM
WIDTH
20
mm
CRUSHER, WHEELED EXCAVATOR,
Compatible equipment models: 1174473:
Number on catalog scheme:
24
For full view, you need register
1174473
Images:
Information:
Personal injury or death may result from failure to adhere to the following procedures.Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.Clean up all leaked or spilled fuel. Do not smoke while working on the fuel system.Turn the disconnect switch OFF or disconnect the battery when changing fuel filters.
Do not fill the fuel filters with fuel before installing the fuel filters. The fuel will not be filtered and could be contaminated. Contaminated fuel will cause accelerated wear to fuel system parts.
The primary filter/water separator is located behind the access door on the right side of the machine.
Illustration 1 g06279640
Open the access door on the right side of the machine.
Illustration 2 g06281993
(1) Filter base
(2) Fuel shutoff valve
(3) Filter housing
(4) Drain valve
(5) Sensor
Turn fuel shutoff valve (2) to the closed position.Note: Refer to Operation and Maintenance Manual, "Fuel Tank Shutoff and Drain Control" for information on the fuel shutoff valve.
Turn drain valve (4) counterclockwise to open. The drain valve is on the bottom of the water separator.Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information that pertains to containing fluid spillage.Note: Dispose of used fluids according to local regulations.
Close the drain valve (4).
Disconnect the water sensor (5) from the harness.Note: Do not attempt to remove the sediment bowl from the housing. The sediment bowl is permanently attached to the housing. Attempting to remove the sediment bowl may damage the bowl.Note: Do not use a chain type strap wrench to remove the fuel filter. Only use a filter wrench on the reinforced area (area with both horizontal and vertical reinforcing ribs) of the filter housing.
Unscrew filter housing (3). Rotate and remove a primary filter from drain valve (4). A filter wrench may be used on the filter housing to loosen the filter housing. Do not apply wrench to clear sediment bowl. Properly discard the used filter.
Clean the mounting base (1).
Lubricate the seal of the new filter with clean diesel fuel.
Install the new filter into the housing.
Tighten the filter housing (3) on the filter base (1) and tighten until the housing flange touches the filter base. Tighten the drain valve (4). Do not use tools to tighten the filter housing to the filter base.
Ensure that sensor (5) is in the correct position and connect to the wiring harness. If the sensor was removed from the bowl, install the sensor and tighten to 2.0 0.2 N m (18 2 lb in).
Open the fuel shutoff valve (2).
Close the access door.
Prime the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
320B, 320C, 322B L, 322B LN, 322C, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L...
1390, 2590, 320C, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329E, 330B L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 345B, 345B II, 345B ...
320C, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329E, 330B L, 330C, 330C FM...
345C, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, AD45B, CR20, P16
16M, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, AD30
320B, 320C, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 330B, 330B L, 330C, 330...
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 365B II, 568 FM LL, M325B, M325C MH, M325D L MH
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, ...
320 L, 320N, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 350, 350 L, 5080
365B, 365B L, 375, 5080
345C, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, CR20, S25
328D LCR, 329D L, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D L, 336D L, 345B II, 345B II MH, 345B L, 345D L, 350, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 5080,...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 16...
1474214
SEAL-O-RING
307B
307B
1474244
SEAL-O-RING
307B
307B
307B
1336784
SEAL-BUFFER
307B, 307C, 308C, 324D L, 330D L
307B, 307C, 308C, 324D L, 330D L
307B, 312C L
1450517
SEAL
307B
307B
1557688
SEAL
307B, 525B, 525C, 535B, 535C, 545, 545C, 902, 906, 908, 950H, 962H, 966H, 972H, 980H, 986H, D5R LGP, D6N, D6N LGP, D6N OEM
307B, 525B, 525C, 535B, 535C, 545, 545C, 902, 906, 908, 950H, 962H, 966H, 972H, 980H, 986H, D5R LGP, D6N, D6N LGP, D6N OEM
1801712
SEAL
307B
307B
1762879
SEAL
307B
307B
1801711
SEAL
307B
307B
1801710
SEAL
307B
307B