1214794 SEAL Caterpillar parts
307B, 311B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320 L, 320B, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 345B II, 345B L, M313C, M315C, M316C, M318C, M318C MH, M322C
Rating:
Alternative (cross code) number:
CA1214794
121-4794
1214794
CA1214794
121-4794
1214794
Weight: 0.02 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 1214794:
Number on catalog scheme:
48
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M8 by 50 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g02191814
If necessary, follow Step 1.a through Step 1.d in order to assembly the engine oil cooler.
Ensure that engine oil cooler matrix (19) is clean, free from damage and restriction. Replace engine oil cooler matrix (19) if damaged or restricted.
Ensure that spacer plate (17) is clean and free from damage. Replace spacer plate (17) if damaged.
Position a new gasket (18) onto spacer plate (17). Install engine oil cooler matrix (19) to the spacer plate.
Install bolts (16) finger tight.
Illustration 2 g02192853
Illustration 3 g03195397
Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base
Clean the gasket surfaces of the cylinder block.
Install Tooling (A) into Position (B).
Position a new gasket (15) (not shown) onto Tooling (A).
Install the assembly of engine oil cooler (14) to the cylinder block.
Install bolts (13) to engine oil cooler (14). Note: Ensure that the bolts of different lengths are installed in the correct position. Ensure that any brackets for the tube assemblies are location and correctly orientated.
Tighten bolts (13) and bolts (16) to a torque of 22 N m (195 lb in) in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g02191813
If the engine has a low mounted oil filter on the left-hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure. If the engine has a right-hand side oil filter, follow Step 9.a through Step 9.d in order to install blanking plate (8).
Install bolts (10) to blanking plate (8).
Position a new gasket (9) (not shown) onto blanking plate (8).
Install the assembly of blanking plate (8) to the assembly of the engine oil cooler.
Tighten bolts (10) to a torque of 22 N m (195 lb in).
Position bracket (6) onto engine oil cooler. Install bolt (7). Tighten bolts (7) to a torque of 22 N m (195 lb in). Note: Ensure that locating pin for the bracket is correctly located into the engine oil cooler.
Install bolt (1) to fuel injection line clamp (2). Tighten bolts (1) to a torque of 10 N m (88 lb in).
Install new cable straps (3) to the engine wiring harness assembly.
Install plastic tube assembly (4) to crankcase breather canister (5) and to the plastic tube assembly clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Install plastic tube assembly (12) to crankcase breather canister (5) and crankcase breather valve (11). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Fill the cooling system to the correct level. Refer to Operation
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M8 by 50 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g02191814
If necessary, follow Step 1.a through Step 1.d in order to assembly the engine oil cooler.
Ensure that engine oil cooler matrix (19) is clean, free from damage and restriction. Replace engine oil cooler matrix (19) if damaged or restricted.
Ensure that spacer plate (17) is clean and free from damage. Replace spacer plate (17) if damaged.
Position a new gasket (18) onto spacer plate (17). Install engine oil cooler matrix (19) to the spacer plate.
Install bolts (16) finger tight.
Illustration 2 g02192853
Illustration 3 g03195397
Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base
Clean the gasket surfaces of the cylinder block.
Install Tooling (A) into Position (B).
Position a new gasket (15) (not shown) onto Tooling (A).
Install the assembly of engine oil cooler (14) to the cylinder block.
Install bolts (13) to engine oil cooler (14). Note: Ensure that the bolts of different lengths are installed in the correct position. Ensure that any brackets for the tube assemblies are location and correctly orientated.
Tighten bolts (13) and bolts (16) to a torque of 22 N m (195 lb in) in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g02191813
If the engine has a low mounted oil filter on the left-hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure. If the engine has a right-hand side oil filter, follow Step 9.a through Step 9.d in order to install blanking plate (8).
Install bolts (10) to blanking plate (8).
Position a new gasket (9) (not shown) onto blanking plate (8).
Install the assembly of blanking plate (8) to the assembly of the engine oil cooler.
Tighten bolts (10) to a torque of 22 N m (195 lb in).
Position bracket (6) onto engine oil cooler. Install bolt (7). Tighten bolts (7) to a torque of 22 N m (195 lb in). Note: Ensure that locating pin for the bracket is correctly located into the engine oil cooler.
Install bolt (1) to fuel injection line clamp (2). Tighten bolts (1) to a torque of 10 N m (88 lb in).
Install new cable straps (3) to the engine wiring harness assembly.
Install plastic tube assembly (4) to crankcase breather canister (5) and to the plastic tube assembly clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Install plastic tube assembly (12) to crankcase breather canister (5) and crankcase breather valve (11). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Fill the cooling system to the correct level. Refer to Operation
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C L MH
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C L MH
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
330, 330B, 330B L, OEMS
330, 330 L, 345B, 345B II, 345B L, 350, OEMS
330C, 330C FM, 330C L, 330C MH
330C, 330D L, 330D MH, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 312B L, 315B L, 317B LN, 318B, 320B, 320C FM, 320D, 320D FM, 320D FM RR, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 32...
2384C, 2484C, 303, 307, 307C, 308C, 308E, 308E CR, 308E SR, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C L, 312D, 312D L, 312E, 312E L, 313B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B, 31...
1426742
SEAL-O-RING
312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320C, 320D, 320D LRR, 321C, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D L, 3...
312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320C, 320D, 320D LRR, 321C, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325B L, 325C, 325D, 325D FM, 325D L, 3...
1538748
SEAL
311B, 311C, 312B L, 312C, 313B, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320B U, 320C, 320D, 320D L, 320D LRR, 321C, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325B...
311B, 311C, 312B L, 312C, 313B, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320B U, 320C, 320D, 320D L, 320D LRR, 321C, 322B LN, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 325B...
2384C, 2484C, 308E, 311, 311B, 312B, 312B L, 313B, 315B, 315B FM L, 315B L, 317B LN, 318B, 318E L, 319D L, 319D LN, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B L, 315C...
1184771
SEAL-O-RING
303.5C, 304C CR, 304D CR, 305C CR, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D4C III, D5C III, D5G
303.5C, 304C CR, 304D CR, 305C CR, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D4C III, D5C III, D5G
1355786
SEAL
315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319D L, 319D LN
315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319D L, 319D LN
303, 307, 312B, 315, 315B, 315C, 317B LN, 318B, 325C, 330C, 330C L, 345C, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300...
315B, 315C, 317B LN, 318B, 318C, 319C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 323D L, 323D LN, 323D SA
311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR, 315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320B, 320B L, 320B U, 320C, 320C FM, 320C...
1262150
SEAL-BUFFER
311B, 315B L, 317B LN, 318B
311B, 315B L, 317B LN, 318B