1289269 SEAL Caterpillar parts
322B, 325B, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L
Rating:
Alternative (cross code) number:
CA1289269
128-9269
1289269
CA1289269
128-9269
1289269
Weight: 0.06 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
15 Jan 2019
75 Hundredths Pounds
Hercules: Hercules
1289269 U-Seal Fits Caterpillar 105x120x10
Warranty
Warranty
Number on catalog scheme:
16
For full view, you need register
Compatible equipment models: 1289269:
Information:
System Operation Description:Use this procedure to troubleshoot the electrical system if a problem is suspected with the sensors or if any one of the diagnostic codes in Table 1 is active or easily repeated.
Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
110-3 Engine Coolant Temperature Sensor voltage above normal The Electronic Control Module (ECM) detects signal voltage that is above normal for eight seconds.
The engine has been running for seven minutes.
An engine coolant temperature that is less than
−35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
90 °C (194 °F).
110-4 Engine Coolant Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
An engine coolant temperature that is greater than
140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
90 °C (194 °F).
172-3 Intake Manifold Air Temperature Sensor voltage above normal The ECM detects signal voltage that is above normal for eight seconds.
An intake manifold air temperature that is less than
−35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
70 °C (158 °F).
172-4 Intake Manifold Air Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
An intake manifold air temperature that is greater than
140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
70 °C (158 °F). System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Engine coolant temperature sensor
Intake manifold air temperature sensor
Fuel temperature sensorThe sensor signal for the passive sensors is routed to terminal 1 of each sensor connector. The analog return for the passive sensors is routed from the ECM to terminal 2 of each sensor connector.
Illustration 1 g01372453
Schematic for the analog sensors
Illustration 2 g01372614
Locations of the analog sensors (typical left side engine view) (1) Engine coolant temperature sensor (2) Intake manifold air temperature sensor (3) Fuel harness connector (4) J2/P2 ECM connectors
Illustration 3 g01372463
Terminal locations at the P2 ECM connector for the analog sensors (P2-13) Engine coolant temperature (P2-30) Sensor return (P2-56) Intake manifold air temperature (P2-62) Fuel temperature
Illustration 4 g01218763
Terminal locations at the sensor connector for the analog sensors (Terminal 1) Sensor signal (Terminal 2) Sensor returnTest Step 1. Check for "Active" or "Logged" Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore power to the ECM.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes.Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Determine if the problem is active and related to one of the following diagnostic codes:
3 Voltage above normal
4 Voltage below normalExpected Result:No diagnostic codes are
Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
110-3 Engine Coolant Temperature Sensor voltage above normal The Electronic Control Module (ECM) detects signal voltage that is above normal for eight seconds.
The engine has been running for seven minutes.
An engine coolant temperature that is less than
−35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
90 °C (194 °F).
110-4 Engine Coolant Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
An engine coolant temperature that is greater than
140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
90 °C (194 °F).
172-3 Intake Manifold Air Temperature Sensor voltage above normal The ECM detects signal voltage that is above normal for eight seconds.
An intake manifold air temperature that is less than
−35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
70 °C (158 °F).
172-4 Intake Manifold Air Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
An intake manifold air temperature that is greater than
140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to
70 °C (158 °F). System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Engine coolant temperature sensor
Intake manifold air temperature sensor
Fuel temperature sensorThe sensor signal for the passive sensors is routed to terminal 1 of each sensor connector. The analog return for the passive sensors is routed from the ECM to terminal 2 of each sensor connector.
Illustration 1 g01372453
Schematic for the analog sensors
Illustration 2 g01372614
Locations of the analog sensors (typical left side engine view) (1) Engine coolant temperature sensor (2) Intake manifold air temperature sensor (3) Fuel harness connector (4) J2/P2 ECM connectors
Illustration 3 g01372463
Terminal locations at the P2 ECM connector for the analog sensors (P2-13) Engine coolant temperature (P2-30) Sensor return (P2-56) Intake manifold air temperature (P2-62) Fuel temperature
Illustration 4 g01218763
Terminal locations at the sensor connector for the analog sensors (Terminal 1) Sensor signal (Terminal 2) Sensor returnTest Step 1. Check for "Active" or "Logged" Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore power to the ECM.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes.Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Determine if the problem is active and related to one of the following diagnostic codes:
3 Voltage above normal
4 Voltage below normalExpected Result:No diagnostic codes are
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
330C, 330C FM, 330C L, 330C MH
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
330B, 330B L, 330C L, 330D, 330D L, 336D
330B, 330B L, 330C L, 330D, 330D L, 336D
330B, 330B L
330, 330B
325B
320N, 322B, 325 L, 325B, 330, 330B, 330B L
1359059
SEAL KIT (FOR HIGH TEMPERATURE)
320N, 330, 330 FM L
320N, 330, 330 FM L
0963998
SEAL
320 L, E180, E200B, E240, E240C, EL240B
320 L, E180, E200B, E240, E240C, EL240B
320B L, E200B
320B
1355790
SEAL
320B
320B
320B