SEAL GP-HDD 1330465 - Caterpillar

Illustration 1 g02642076
Table 1
Specification for 333-3036 Final Drive Gp
Item Qty Part Specification Description
1 20 Bolt Before assembly, the contact surfaces of the bolts, the washers, and the tightened parts must be clean and free from protective coating and oil.
Torque to 900 100 N m (664 74 lb ft).
2 2 3E-2338 Pipe Plug Torque to 80 10 N m (59 7 lb ft).
3 6 114-1541 Dowel Pin Before assembly, apply Loctite C5A Copper Anti-Seize to the inside diameter and outside diameter of the mating parts of the dowel pins.
4 1 Duo-Cone Seal Gp Rubber toric seals and all surfaces in contact with the seals must be clean and dry at assembly. Apply a thin layer of 6V-4876 Lubricant on the surfaces of the metal seals that are in contact just before installation. The metal seal must be assembled square with the bore. The rubber toric seals must not bulge. The rubber toric seals must not be twisted.
5 1 7Y-0808 Shim As required, use the following shim in order to adjust the clearance (C).
Thickness is 1.6 (0.06 inch).
C - - Clearance is 1.0 to 2.6 mm (0.04 to 0.10 inch).
6 2 2R-0524 Bearing Cone Apply Loctite C5A Copper Anti-Seize to the inside diameter and outside diameter of the mating parts.
7 2 2R-0525 Bearing Cup Apply Loctite C5A Copper Anti-Seize to the inside diameter and outside diameter of the mating parts.
8 10 8T-3957 Bolt Before assembly, the contact surfaces of the bolts, the washers, and the tightened parts must be clean and free from protective coating and oil.
9 1 7Y-1483 Ring Gear Before assembly, apply 1U-8846 Gasket Sealant to the mating parts.
10 1 7Y-1498 Cover Before assembly, apply 1U-8846 Gasket Sealant to the mating parts.
12 As required, use the following shims. If two shims are required, install the thinner shim next to coupling gear (11).
1 7Y-1472 Shim Thickness is 0.15 0.03 mm (0.006 0.001 inch).
1 7Y-1473 Shim Thickness is 0.30 0.04 mm (0.012 0.002 inch).
1 7Y-1474 Shim Thickness is 0.40 0.05 mm (0.016 0.002 inch).
1 7Y-1475 Shim Thickness is 0.50 0.05 mm (0.020 0.002 inch).
1 7Y-1476 Shim Thickness is 0.60 0.06 mm (0.024 0.002 inch).
1 7Y-1477 Shim Thickness is 0.70 0.06 mm (0.028 0.002 inch).
1 7Y-1478 Shim Thickness is 0.80 0.07 mm (0.031 0.003 inch).
1 7Y-1479 Shim Thickness is 1.00 0.08 mm (0.039 0.003 inch).
1 7Y-1480 Shim Thickness is 1.60 0.10 mm (0.063 0.004 inch).
13 12 6V-8133 Bolt Before assembly, the contact surfaces of the bolts, the washers, and the tightened parts must be clean and free from protective coating and oil. Apply blue Loctite 242 to the threads.
Torque to 900 100 N m (664 74 lb