AVSPARE.COM
parts catalog

SEAL-U-CUP 1400244 - Caterpillar



1400244 SEAL-U-CUP Caterpillar parts SEAL
Rating:
16
Alternative (cross code) number:
CA1400244
140-0244
1400244
Caterpillar 1400244 SEAL-U-CUP
Weight: 0.11 pounds 0 kg.

Buy SEAL-U-CUP 1400244 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

2. Fasten tooling (B) to the tandem housing as shown. Move the tandem housing toward the final drive until tool (C) just comes in contact with the shaft in the final drive. The weight of the tandem housing is approximately 3600 lb. (1633 kg).3. Hand tighten tool (C) on to the shaft in the final drive. Move the tandem housing toward the machine. The drive sprockets will slide off of tool (C) and on to the shaft in the final drive. 4. Install nuts (2) that hold the tandem housing to the final drive. Tighten the nuts to a torque of 350 15 lb.ft. (475 20 N m).5. Remove tool (C). 6. Use tool (D) and the following procedure to get the correct preload on the final drive bearings.a) Turn the tires as the nut is tightened to a torque of 125 lb.ft. (169 N m).b) Hit the hub of the sprocket with a large punch and a hammer.c) Do Steps 6a and 6b again until the sprocket nut will not turn when a torque of 125 lb.ft. (169 N m) is used to tighten the nut.d) Loosen the nut.e) Tighten the nut to a torque of 75 lb.ft. (102 N m).f) One of the notches in the nut must be in alignment with a hole in the sprocket. Tighten the nut if necessary to get the nut and sprocket in alignment. 7. Connect air line (3). Close the bleed valves on the air tank.8. Lower the machine to the ground. Remove tooling (E).END BY:a) install axleDisassemble Final Drives
START BY:a) remove final drives 1. Remove bearing cone (1) and O-ring seal (2) from the housing. 2. Put the final drive in position on its end with the planet carrier up as shown. Remove sun gear (3). 3. Fasten a hoist to the planet carrier. Remove planet carrier (4). The weight of the planet carrier is 170 lb. (77 kg). 4. Remove the bolts, locks and retainer (5) that hold shaft (6) in position. 5. Remove shaft (6). Remove gear (7) from the carrier. Remove two roller assemblies (8) and washer (9) from each gear. There is a washer on both sides of each gear. Remove the spacer between the two roller assemblies. 6. Remove ring (10) with tool (A). Remove washer (11). 7. Use a pry bar as a support for gear (12). Remove the bolts, locks and plates (13) that hold gear (12) in place. Use the pry bar to lift the gear enough to install three straps around the gear. Fasten a hoist to the three straps and remove gear (12). The weight of the gear is approximately 98 lb. (44 kg). 8. Put the final drive on its side as shown. Pull shaft (14) out of the final drive part way. Fasten a strap and a hoist to shaft (14) and remove it from the housing. The weight of the shaft is approximately 80 lb. (36 kg). 9. Use tooling (B) to remove


Parts seal Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.