1410706 SEAL-BUFFER Caterpillar parts
902, 906
Rating:
Alternative (cross code) number:
CA1410706
141-0706
1410706
CA1410706
141-0706
1410706
Weight: 0.02 pounds 0 kg.
Information:
GROOVE AXIAL WIDTH
6.4
mm
GROOVE DIAMETER
65.5
mm
MATERIAL
Urethane Rubber - 90 Duro
ROD DIAMETER
49.95
mm
COMPACT WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement Pintle Chain Gearbox Coupler (1 EA)
Buyers Products Company Buyers Product Company
Buyers Products Company Buyers Product Company
1410706 1410706 Drive Shaft Gearbox Flex Chain - Replace 3003485 1410706
GENERIC
GENERIC
$14.99
28 Feb 2024
US: Avon Surgical
NEW SET OF 5 PCS PARAMEDIC UTILITY BANDAGE TRAUMA EMT EMS SHEARS SCISSORS 7.25 INCH STAINLESS STEEL
Cynamed 1 EA EMT Shear Scissors Bandage 7.25" Black || 1 EA EMT Shear Scissors Bandage 7.25" RED || 1 EA EMT Shear Scissors Bandage 7.25" BlUE || 1 EA EMT Shear Scissors Bandage 7.25" PINK || 1 EA EMT Shear Scissors Bandage 7.25" YELLOW
Cynamed 1 EA EMT Shear Scissors Bandage 7.25" Black || 1 EA EMT Shear Scissors Bandage 7.25" RED || 1 EA EMT Shear Scissors Bandage 7.25" BlUE || 1 EA EMT Shear Scissors Bandage 7.25" PINK || 1 EA EMT Shear Scissors Bandage 7.25" YELLOW
Number on catalog scheme:
7
For full view, you need register
1410706
Images:
Information:
and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ether Switch
Remove the ether canister from the ether solenoid.
Connect the Cat ET to the service tool connector.
Turn the keyswitch to the ON position.
Press the starting aid switch to "MANUAL". Observe the status of "Ether Switch" on Cat ET. Expected Result:When the starting aid switch is pressed, Cat ET displays the status of the switch as "On".When the starting aid switch is not pressed, Cat ET displays the status of the switch as "Off".Results:
OK - The starting aid switch is operating correctly. Proceed to Test Step 5.
Not OK - There may be a problem with the switch circuit. Proceed to Test Step 3.Test Step 3. Short the Switch Wires
Turn the keyswitch to the ON position.
Disconnect the starting aid switch.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "Off".
Install a jumper wire between terminal 2 and terminal 3 in the plug for the starting aid switch.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "On".Expected Result:When the terminals are shorted, Cat ET displays the status of the starting aid switch as "On".When the terminals are not shorted, Cat ET displays the status of the starting aid switch as "Off".Results:
OK - The ECM and the harness are OK, but the starting aid switch is not operating correctly.Repair: Replace the starting aid switch.Verify that the repair eliminates the problem.STOP
Not OK - There may be a problem with the harness. Proceed to Test Step 4.Test Step 4. Short the Switch Inputs at the ECM
Turn the keyswitch to the OFF/RESET position.
Remove the wires from P1:22 (Starting Aid Switch) and P1:5 (Digital Return).
Turn the keyswitch to the ON position.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "Off".
Install a jumper wire with Deutsch sockets on each end between P1:22 (Starting Aid Switch) and P1:5 (Digital Return).
Turn the keyswitch to the ON position.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "On".
Remove the jumper wire and reinstall the wires in the P1 connector. Expected Result:When the jumper wire is installed, Cat ET displays the status of the switch as "On".When the jumper wire is not installed, Cat ET displays the status of the starting aid switch as "Off".Results:
OK - The ECM is operating correctly. There is a problem in the wiring between the switch and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - There is a problem with the solenoid circuit or the ECM.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ether Switch
Remove the ether canister from the ether solenoid.
Connect the Cat ET to the service tool connector.
Turn the keyswitch to the ON position.
Press the starting aid switch to "MANUAL". Observe the status of "Ether Switch" on Cat ET. Expected Result:When the starting aid switch is pressed, Cat ET displays the status of the switch as "On".When the starting aid switch is not pressed, Cat ET displays the status of the switch as "Off".Results:
OK - The starting aid switch is operating correctly. Proceed to Test Step 5.
Not OK - There may be a problem with the switch circuit. Proceed to Test Step 3.Test Step 3. Short the Switch Wires
Turn the keyswitch to the ON position.
Disconnect the starting aid switch.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "Off".
Install a jumper wire between terminal 2 and terminal 3 in the plug for the starting aid switch.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "On".Expected Result:When the terminals are shorted, Cat ET displays the status of the starting aid switch as "On".When the terminals are not shorted, Cat ET displays the status of the starting aid switch as "Off".Results:
OK - The ECM and the harness are OK, but the starting aid switch is not operating correctly.Repair: Replace the starting aid switch.Verify that the repair eliminates the problem.STOP
Not OK - There may be a problem with the harness. Proceed to Test Step 4.Test Step 4. Short the Switch Inputs at the ECM
Turn the keyswitch to the OFF/RESET position.
Remove the wires from P1:22 (Starting Aid Switch) and P1:5 (Digital Return).
Turn the keyswitch to the ON position.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "Off".
Install a jumper wire with Deutsch sockets on each end between P1:22 (Starting Aid Switch) and P1:5 (Digital Return).
Turn the keyswitch to the ON position.
Observe the status of "Ether Switch" on Cat ET. Note: The status should be "On".
Remove the jumper wire and reinstall the wires in the P1 connector. Expected Result:When the jumper wire is installed, Cat ET displays the status of the switch as "On".When the jumper wire is not installed, Cat ET displays the status of the starting aid switch as "Off".Results:
OK - The ECM is operating correctly. There is a problem in the wiring between the switch and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - There is a problem with the solenoid circuit or the ECM.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
1890592
SEAL
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1890218
SEAL-WIPER
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1890217
SEAL-U-CUP
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1890213
SEAL AS
902, 906, 906H, 907H, 908, 908H
902, 906, 906H, 907H, 908, 908H
1402310
SEAL-BUFFER
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, AD30, AD45B
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, AD30, AD45B
120G, 902, 906, 908, 910
1707609
SEAL
906
906
1449929
SEAL
902, 906, 908
902, 906, 908
2334187
SEAL
902, 906, 908
902, 906, 908
1557222
SEAL
902, 906, 908
902, 906, 908
1557218
SEAL-COVER
902, 906, 908
902, 906, 908
