1428075 SEAL-LIP TYPE Caterpillar parts
69D, 769C, 769D, 771C, 771D, 773B, 773D, 773E, 775B, 775D, 775E, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II
Rating:
Alternative (cross code) number:
CA1428075
142-8075
1428075
CA1428075
142-8075
1428075
Weight: 0.30 pounds 0 kg.
Information:
AXIAL WIDTH
12.7
mm
BORE DIAMETER
104.78
mm
CONSTRUCTION TYPE
DBI
MATERIAL
FKM Rubber - 80 Duro
SEAL OD
104.9
mm
SHAFT OD
79.38
mm
QUARRY TRUCK, UNDERGROUND ART TRUCK,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Number on catalog scheme:
21
For full view, you need register
Compatible equipment models: 1428075:
Information:
OP6 is the option for programming of the spare inputs. OP6 is the option for programming the spare output. These spare inputs and spare outputs are provided in order to satisfy the needs of the customer.Spare Inputs
The spare inputs are referred to as SP1, SP2, and SP3. The spare inputs are accessed on the auxiliary terminal strip (AUX) within the control panel on the left wall. The terminations at the auxiliary terminal strip for the spare inputs are marked. SP1 is marked as "SW1". SP2 is marked as "SW2". SP3 is marked as "SW3".The following tasks for each spare input are programmable: active input state, response taken and time delay. The GSC responds to the active state of an input, although the response can be delayed. Setpoints SP01 through SP06 and SP08 through SP10 are used for programming the spare inputs. Each of the setpoints is described in the following topics.
Illustration 1 g00308511
Typical Active High Input Configuration For Spare Input 1 (SP1)
Illustration 2 g00307940
Typical Active Low Input Configuration For Spare Input 1 (SP1)The active input state must be programmed into the GSC. A high state is 5 DCV to B+. A low state is B-. When an input is programmed for an active high state a high state at the input is a spare fault. A low state at the input is a normal condition. When an input is programmed for an active low state, a low state at the input is a spare fault. A high state at the input is a normal condition. Setpoints SP01, SP03 and SP05 are used for the programming of the active input state of the spare inputs.Note: If an input is left floating, then the internal circuitry of the GSC pulls the input high. The GSC will respond accordingly.The GSC response to an active spare fault must be programmed. One response option treats the condition as a shutdown fault. The other response option treats the condition as an alarm fault. Setpoints SP02, SP04, and SP06 are used for programming the response.Note: Spare faults that are programmed to shutdown are ignored by the GSC when engine speed is less than crank termination speed. The GSC must be programmed for the amount of time to delay the response to a spare fault (active input). After a spare fault occurs, the GSC does not respond until the time delay has elapsed. Indicators are not activated. Codes are not shown. The operation of the engine has not changed. Setpoints SP08, SP09, and SP10 are used for programming the time delay. The time delay is selectable from 0 to 250 seconds.SP01 Spare Input 1 Active State
The spare inputs are referred to as SP1, SP2, and SP3. The spare inputs are accessed on the auxiliary terminal strip (AUX) within the control panel on the left wall. The terminations at the auxiliary terminal strip for the spare inputs are marked. SP1 is marked as "SW1". SP2 is marked as "SW2". SP3 is marked as "SW3".The following tasks for each spare input are programmable: active input state, response taken and time delay. The GSC responds to the active state of an input, although the response can be delayed. Setpoints SP01 through SP06 and SP08 through SP10 are used for programming the spare inputs. Each of the setpoints is described in the following topics.
Illustration 1 g00308511
Typical Active High Input Configuration For Spare Input 1 (SP1)
Illustration 2 g00307940
Typical Active Low Input Configuration For Spare Input 1 (SP1)The active input state must be programmed into the GSC. A high state is 5 DCV to B+. A low state is B-. When an input is programmed for an active high state a high state at the input is a spare fault. A low state at the input is a normal condition. When an input is programmed for an active low state, a low state at the input is a spare fault. A high state at the input is a normal condition. Setpoints SP01, SP03 and SP05 are used for the programming of the active input state of the spare inputs.Note: If an input is left floating, then the internal circuitry of the GSC pulls the input high. The GSC will respond accordingly.The GSC response to an active spare fault must be programmed. One response option treats the condition as a shutdown fault. The other response option treats the condition as an alarm fault. Setpoints SP02, SP04, and SP06 are used for programming the response.Note: Spare faults that are programmed to shutdown are ignored by the GSC when engine speed is less than crank termination speed. The GSC must be programmed for the amount of time to delay the response to a spare fault (active input). After a spare fault occurs, the GSC does not respond until the time delay has elapsed. Indicators are not activated. Codes are not shown. The operation of the engine has not changed. Setpoints SP08, SP09, and SP10 are used for programming the time delay. The time delay is selectable from 0 to 250 seconds.SP01 Spare Input 1 Active State
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
769, 772, 773B, 776, 777
769, 772, 773B, 776, 777
769C
120B, 12E, 140, 140B, 769, 769C, 824
773B
768C, 769C
773B
AD40, AD45, AD45B, AE40, AE40 II
320B, 320C, 322B L, 322B LN, 322C, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L...
1390, 2590, 320C, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329E, 330B L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 345B, 345B II, 345B ...
320C, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329E, 330B L, 330C, 330C FM...
1608181
SEAL-LIP TYPE
769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D
769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D
789, 789B, 789C, 789D
785, 789, 789B, 789C, 789D
785, 785C, 789, 789B, 789C, 789D
789, 789B, 789C, 789D
789B, 789C, 789D
24H, 24M, 772B, 773B, 773D, 775B, 775D, 776D, 777, 777B, 777D, PM-201, PM-565, PM-565B
735B, 740B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
773B, 773D, 775B, 775D, 776D, 777D
769C, 769D, 770G, 771C, 771D, 772G, 773B, 773D, 773E, 773G, 773G LRC, 775B, 775E, 775G, 775G LRC, 775G OEM, AD55, AD55B
69D, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, AD40, AD45, AD45B...
69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, AD45, AE40 II