1540729 SEAL-LIP TYPE Caterpillar parts
320B, 320B L, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 325C L
Rating:
Alternative (cross code) number:
CA1540729
154-0729
1540729
CA1540729
154-0729
1540729
Weight: 0.08 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
01 Sep 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Seal 1540729 New
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 1540729:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
B - Block
12 by 12 by 24 1 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starter Motor - Remove and Install".
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01238988
Use Tooling (B) or a suitable block to support the rear of the cylinder block in order to remove flywheel housing (1). The weight of the engine is approximately 1814 kg (4000 lb).
Illustration 2 g01239002
Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of flywheel housing (1) is approximately 105 kg (230 lb).
Remove bolts (2). Remove flywheel housing (1) from the cylinder block.
Remove gasket (3) from flywheel housing (1).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
C - Loctite Superflex Silicone Adhesive Sealant, Blue -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01239002
Thoroughly clean flywheel housing (1) and the rear face of the cylinder block.
Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of flywheel housing (1) is approximately 105 kg (230 lb).
Install gasket (3) on the dowel pins of the cylinder block. Apply Tooling (C) to the bottom of gasket (3) in order to fill the space at the cylinder block, flywheel housing (1), and the engine oil pan.
Position flywheel housing (1) and install bolts (2).
Illustration 4 g00551652
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt (1) through Bolt (24) to a torque of 40 10 N m (30 7 lb ft).
In a numerical sequence, again tighten Bolt (1) through Bolt (9) to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, again tighten Bolt (10) through Bolt (24) to a torque of 55 10 N m (40 7 lb ft).
Remove Tooling (A).End By:
Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install".
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
B - Block
12 by 12 by 24 1 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starter Motor - Remove and Install".
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Remove the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01238988
Use Tooling (B) or a suitable block to support the rear of the cylinder block in order to remove flywheel housing (1). The weight of the engine is approximately 1814 kg (4000 lb).
Illustration 2 g01239002
Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of flywheel housing (1) is approximately 105 kg (230 lb).
Remove bolts (2). Remove flywheel housing (1) from the cylinder block.
Remove gasket (3) from flywheel housing (1).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
C - Loctite Superflex Silicone Adhesive Sealant, Blue -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01239002
Thoroughly clean flywheel housing (1) and the rear face of the cylinder block.
Install Tooling (A) and a suitable lifting device on flywheel housing (1). The weight of flywheel housing (1) is approximately 105 kg (230 lb).
Install gasket (3) on the dowel pins of the cylinder block. Apply Tooling (C) to the bottom of gasket (3) in order to fill the space at the cylinder block, flywheel housing (1), and the engine oil pan.
Position flywheel housing (1) and install bolts (2).
Illustration 4 g00551652
Tighten the bolts, as follows:
In a numerical sequence, tighten Bolt (1) through Bolt (24) to a torque of 40 10 N m (30 7 lb ft).
In a numerical sequence, again tighten Bolt (1) through Bolt (9) to a torque of 135 20 N m (100 15 lb ft).
In a numerical sequence, again tighten Bolt (10) through Bolt (24) to a torque of 55 10 N m (40 7 lb ft).
Remove Tooling (A).End By:
Install the engine speed sensor. Refer to Disassembly and Assembly, "Engine Speed Sensor - Remove and Install".
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
320D, 320D FM, 320D L, 320D2, 320D2 L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320B
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
1843901
SEAL
320B, 320B U
320B, 320B U
1557102
SEAL
320B, 320B L, 320B U
320B, 320B L, 320B U
1241586
SEAL
320B, 320B L, 320B U, 321B
320B, 320B L, 320B U, 321B
1627750
SEAL
M320
M320
1265253
SEAL
M320
M320
320 L, 320B, 320N, 322B, 322B LN, 325, 325 L, 325 LN, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330C L, 345B II, 345B L, M325B
320B, 320C, 322B, 322C, 324D, 324D L, 325B, 325C, 330C L
320B, 320B FM LL, 320C, 320C FM, 322, 322B, 322C, 325B, 375
320B, 320B FM LL, 320C, 320C FM, 320D, 321B, 321C, 321D LCR, 322, 322B, 322C, 324D, 324D L, 325B, 325C, 325C L, 328D LCR, 330C L, 375
320B, 320B FM LL, 320C, 320C FM, 320D, 320E, 320E L, 320E RR, 321B, 321C, 321D LCR, 322B, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B, 325C, 325C L, 326D L, 328D LCR, 330C L, 375
320B, 320B L, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 325C L
320B, 320B L, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 325C L