1672334 SEAL-U-CUP Caterpillar parts
834G, 834H, TK1051
Rating:
Alternative (cross code) number:
CA1672334
167-2334
1672334
CA1672334
167-2334
1672334
Weight: 0.05 pounds 0 kg.
Information:
GROOVE AXIAL WIDTH
14.1
mm
GROOVE DIAMETER
125.03
mm
MATERIAL
Polyurethane - 90 Duro
ROD DIAMETER
109.93
mm
TYPE
STANDARD
TRACK FELLER BUNCHER, WHEEL DOZER,
Number on catalog scheme:
11
For full view, you need register
Information:
This diagnostic code is recorded when the VIMS ECM is unable to communicate with the engine ECM via the Cat Data Link. Because there is no response from the ECM or the response is incorrect.System Response:This failure results in events that are logged against an ECM that can not be explained. The "VIMS ECM" cannot communicate with this ECM or the ECM appears to work intermittently. Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the “VIMS onboard software”
The part number of the “engine flash software”
The part number of the VIMS ECM
The part number of the engine ECMNote: Consult the Business Unit that produces the product for the correct part numbers of the configuration software.Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. Repair: The installed VIMS ECM or the engine has the wrong part number or the incorrect configuration software is installed. Replace the incorrect VIMS ECM or the engine with a module that has the correct part number. Flash the correct configuration software. See the Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" section of this manual.STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the "VIMS ECM", measure the resistance between frame ground and connector contacts J1-7 (wire 893-GN(Green)) and J1-6 (wire 892-BR(Brown)) of the Cat Data Link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. Repair:
Verify that the following information is correct:
The part number of the “VIMS onboard software”
The part number of the “engine flash software”
The part number of the VIMS ECM
The part number of the engine ECMNote: Consult the Business Unit that produces the product for the correct part numbers of the configuration software.Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. Repair: The installed VIMS ECM or the engine has the wrong part number or the incorrect configuration software is installed. Replace the incorrect VIMS ECM or the engine with a module that has the correct part number. Flash the correct configuration software. See the Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" section of this manual.STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the "VIMS ECM", measure the resistance between frame ground and connector contacts J1-7 (wire 893-GN(Green)) and J1-6 (wire 892-BR(Brown)) of the Cat Data Link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. Repair:
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
322B L, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 328D LCR, 329D LN, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2484C, 2491, 2590, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 ...
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330, 330 FM L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2484C, 2491, 2590, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2484C, 2491, 2590, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 ...
1390, 2590, 320C, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329E, 330B L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 345B, 345B II, 345B ...
1290T, 1390, 2491, 2590, 325D FM, 325D FM LL, 330, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, ...
1290T, 1390, 2491, 2590, 325D FM, 325D FM LL, 330, 330B L, 330C, 330C FM, 330C MH, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH,...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, ...
322B L, 322C, 322C FM, 325B L, M325B, TK1051
322B L, 322C, 322C FM, 325B L, M325B, TK1051
834G, 834H, TK1051
2226716
SEAL
TK1051
TK1051
2667965
SEAL-O-RING
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
2667963
SEAL-O-RING
320C, 322C, 325C
320C, 322C, 325C
2667964
SEAL-O-RING
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 322C
2742502
SEAL-O-RING
320C, 322C
320C, 322C
2114727
SEAL-DOOR
1090, 1190, 1190T, 1290T, 1390, 533, 543, HA770, HA771, HA870, HA871, TK1051, TK370, TK371, TK380, TK381, TK711, TK721, TK722, TK732, TK741, TK751, TK752
1090, 1190, 1190T, 1290T, 1390, 533, 543, HA770, HA771, HA870, HA871, TK1051, TK370, TK371, TK380, TK381, TK711, TK721, TK722, TK732, TK741, TK751, TK752
120G, 12G, 130G, 140G, 14G, 160G, 543, HA770, HA771, HA870, HA871, TK1051, TK370, TK371, TK380, TK381
8C5200
SEAL
322 FM L, 325 L, 330, 330 FM L, 330 L, TK1051
322 FM L, 325 L, 330, 330 FM L, 330 L, TK1051
1672483
SEAL-WIPER
1390, 2590, 325B L, 325C, 325D MH, 330C L, 345B II, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752
1390, 2590, 325B L, 325C, 325D MH, 330C L, 345B II, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752
1390, 2590, 325B L, 325C, 325C L, 325D L, 325D MH, 330B L, 330C L, 330D, 330D L, 336D, 345B, 345B II, 345B II MH, 385B, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752, W330B, W345B II
834G, 834H, TK1051