SEAL 1705966 - Caterpillar

Secure the engine harness assembly (1) to the clip (BH) with the two cable strap (3) behind muffler.
Connect the harness to the camshaft angle sensor (BJ).
Illustration 39 g06199958
(1) 499-8506 Engine Harness As
(BK) Clip
(BL) P-clip
Secure the engine harness assembly (1) to the clip (BK) on the flywheel housing and the p-clip (BL) on the engine support.
Illustration 40 g06199959
(1) 499-8506 Engine Harness As
(BM) Electronic control module (ECM)
(BN) Cable Strap
(BP) Main bundle
Connect the engine harness assembly (1) to the ECM (BM).
Connect the engine harness assembly (1) to the chassis harness, and cable strap (BN) to the main bundle (BP).
Illustration 41 g06199961
(4) 163-6795 Cable Strap
(BR) 790 mm (31.1 inch)
(BS) 540 mm (21.3 inch)
(BT) 100 mm (3.9 inch)
(BU) 400 mm (15.7 inch)
(BW) 15 to 20 mm (0.6 to 0.8 inch)
Illustration 42 g06199963
Detailed view of area BV
(4) 163-6795 Cable Strap
(BT) 100 mm (3.9 inch)
(BX) 90 degrees
Drill four holes of 6.3 mm (0.25 inch) diameter along inner wall of the frame and install four cable strap (4) as shown in Illustration 42.Note: Come out from the inside of the engine compartment 15 to 20 mm (0.6 to 0.8 inch) to drill the holes.Note: All vertical measurements shown in Illustration 42 are measured from the bottom plate.
Illustration 43 g06199964
(4) 163-6795 Cable Strap
(BY) 300 mm (11.8 inch)
(BZ) 100 mm (3.9 inch)
Drill two holes of 6.3 mm (0.25 inch) diameter along the inner wall of the frame and install two cable strap (15) as shown in Illustration 43.Note: All horizontal measurements shown in Illustration 43 are measured from the inside edge of the frame.
Illustration 44 g06199966
(5) 132-5789 Clip
(CA) Intake tube
Install the clip (5) on existing hardware.
Remove cross over intake tube (CA).Note: Cover air inlet on filter housing to prevent contamination on the inlet side of the engine.
Illustration 45 g06199967
(1) 499-8506 Engine Harness As
(2) 7K-1181 Cable Strap
(6) 474-7538 Sensor Harness As
Connect the engine harness assembly (1) to the sensor harness assembly (6) and secure using the cable strap (2).
Illustration 46 g06199969
(4) 163-6795 Cable Strap
(6) 474-7538 Sensor Harness As
Route the sensor harness assembly (6) along with the cable strap (4).
Illustration 47 g06199970
(3) 3S-2093 Cable Strap
(5) 132-5789 Clip
(6) 474-7538 Sensor Harness As
(7) 204-1611 Strap
(CB) Mass air flow sensor
Secure the sensor harness assembly (6) to the clip (5) using the cable strap (3).
Connect the sensor harness assembly (6) to the mass air flow sensor (CB).
Constrain the sensor harness assembly (6) to the connector using the dual strap (7) to control the excess slack.Note: Ensure to allow enough slack so that the pigtail is not pulled tight.Note: Do not allow it to touch the DPF (approximately 150 mm (5.9 inch).