1709850 SEAL-BUFFER Caterpillar parts
312D, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 5080, 5090B, 568 FM LL, 988K, M325B,...
Rating:
Alternative (cross code) number:
CA1709850
170-9850
1709850
CA1709850
170-9850
1709850
Weight: 0.03 pounds 0 kg.
Information:
GROOVE AXIAL WIDTH
6
mm
GROOVE DIAMETER
145.5
mm
MATERIAL
Urethane Rubber - 90 Duro
ROD DIAMETER
129
mm
EXCAVATOR, WHEELED EXCAVATOR,
Cross Reference:
CATERPILLAR
1709850,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$44.24
22 Jun 2023
US: Florida-Parts-Z
1709850 - Seal-Buffer for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$39.39
24 Nov 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL-BUFFER 1709850 NEW
$12.39
08 Jun 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar Seal (1709850)
CTP
CTP
Number on catalog scheme:
20
For full view, you need register
Compatible equipment models: 1709850:
Information:
System Operation Description:If any of the following conditions have occurred, calibrate the injector trim codes:
Replacement of the Electronic Control Module (ECM)
Replacement of any of the unit injectorsA special code is stamped on the top of each unit injector. The injector trim code allows the ECM to compensate for variances in manufacturing.Note: Changing the injector trim codes will not increase the power that is available to the engine.
The connection of any electrical equipment and the disconnection of any electrical equipment may cause an explosion hazard which may result in injury or death. Do not connect any electrical equipment or disconnect any electrical equipment in an explosive atmosphere.
Test Step 1. Record Injector Trim Codes
Use Table 1 to record the injector trim code and the corresponding cylinder number for each unit injector that will be replaced.
Table 1
Injector Trim Code
Cylinder Old New
1
2
3
4
5
6 Note: If the ECM is replaced, all injector trim codes must be recorded. The injector trim codes can be found in "Calibrations" under the "Service" menu on the Caterpillar Electronic Technician (ET).Expected Result:All injector trim codes were obtained.Results:
OK - All injector trim codes were obtained. Proceed to Test Step 2.
Not OK - The injector trim codes were not obtained.Repair: Remove the valve cover and record the injector trim code and the corresponding cylinder number for each unit injector. Proceed to Test Step 2.Test Step 2. Replace Hardware
Remove electrical power from the ECM.
Replace the suspect unit injectors and/or the ECM.
Record the injector trim code and the corresponding cylinder number for each unit injector.Expected Result:All hardware was successfully replaced and the new injector trim codes were recorded.Results:
OK - The hardware was successfully replaced. Proceed to Test Step 3.Test Step 3. Enter Injector Trim Codes into the ECM
Connect Cat ET to the service tool connector.
Restore electrical power to the ECM.
Open the "Injector Codes Calibration" in "Calibrations" under the "Service" menu on Cat ET.
Enter the new injector trim code for each cylinder.Results:
OK - STOP
Replacement of the Electronic Control Module (ECM)
Replacement of any of the unit injectorsA special code is stamped on the top of each unit injector. The injector trim code allows the ECM to compensate for variances in manufacturing.Note: Changing the injector trim codes will not increase the power that is available to the engine.
The connection of any electrical equipment and the disconnection of any electrical equipment may cause an explosion hazard which may result in injury or death. Do not connect any electrical equipment or disconnect any electrical equipment in an explosive atmosphere.
Test Step 1. Record Injector Trim Codes
Use Table 1 to record the injector trim code and the corresponding cylinder number for each unit injector that will be replaced.
Table 1
Injector Trim Code
Cylinder Old New
1
2
3
4
5
6 Note: If the ECM is replaced, all injector trim codes must be recorded. The injector trim codes can be found in "Calibrations" under the "Service" menu on the Caterpillar Electronic Technician (ET).Expected Result:All injector trim codes were obtained.Results:
OK - All injector trim codes were obtained. Proceed to Test Step 2.
Not OK - The injector trim codes were not obtained.Repair: Remove the valve cover and record the injector trim code and the corresponding cylinder number for each unit injector. Proceed to Test Step 2.Test Step 2. Replace Hardware
Remove electrical power from the ECM.
Replace the suspect unit injectors and/or the ECM.
Record the injector trim code and the corresponding cylinder number for each unit injector.Expected Result:All hardware was successfully replaced and the new injector trim codes were recorded.Results:
OK - The hardware was successfully replaced. Proceed to Test Step 3.Test Step 3. Enter Injector Trim Codes into the ECM
Connect Cat ET to the service tool connector.
Restore electrical power to the ECM.
Open the "Injector Codes Calibration" in "Calibrations" under the "Service" menu on Cat ET.
Enter the new injector trim code for each cylinder.Results:
OK - STOP
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
330B, 330B L, 345B, 345B L, W330B
365B, 365B L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
345B II, 345C, 345D, 345D L, 349D, 349D L
345B II, 345C, 345D, 345D L, 349D, 349D L
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
312D, 345B II, 345B L, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 5080, 5090B
312D, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L,...
312D, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C L MH, 966K, 966M, 966M XE, 972...
312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR
312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR
311D LRR, 312E, 314D LCR, 314E LCR, 316E L, 318E L, 623H, 623K, 623K LRC, 953D
3057612
SEAL
314D CR, 314D LCR
314D CR, 314D LCR
3057611
SEAL
314D CR, 314D LCR
314D CR, 314D LCR
3057610
SEAL
314D CR, 314D LCR
314D CR, 314D LCR
2653642
SEAL
314D CR, 314D LCR, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
314D CR, 314D LCR, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
314D CR, 314D LCR, 330C, 330C FM, 330C L, 330C MH
2040894
SEAL
314D CR, 314D LCR, 322C, 325C
314D CR, 314D LCR, 322C, 325C