1709857 SEAL-U-CUP Caterpillar parts
308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315B, 315C, 315D L, 320D, 320D L, 324D, 324D L, 329D, 329D L, 329D LN, 329E L, 329E LN, M312, M313C...
Rating:
Alternative (cross code) number:
CA1709857
170-9857
1709857
CA1709857
170-9857
1709857
Weight: 0.04 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$18.00
24 Apr 2022
US: Florida-Parts-Z
1709857 - Seal-U-Cup for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$15.77
08 Dec 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL-U-CUP 1709857 NEW
$9.51
29 Jun 2022
1.0[0.45] Pounds
US: ProperBuy
1709857 Seal-U-Cup Fits Caterpillar 931477 3046 3054 3054C 3054E 3056E 3064 C4.2
TCP Warranty
TCP Warranty
Number on catalog scheme:
5
For full view, you need register
Compatible equipment models: 1709857:
Information:
Injector Synchronization And Power Setting
Table 1
Tools Needed Quantity
4C-6594 Timing and Fuel Setting Tool 1
6V-9057 Rack Synchronizing Gauge 1
6V-3075 Dial Indicator 1
5P-4814 Collet Clamp 1
5P-7263 Indicator Contact Point 1
4C-6583 Governor Calibration Adapter 1
Illustration 1 g00605849
(1) Control rod assembly (2) Lever (3) Governor output shaft (4) Synchronizing pin (5) Power setting screw in hole "W" (Y) Location for the dial indicator (Z) Location for synchronizing pin
Illustration 2 g00606063
(6) Shaft (7) Fuel stop lever (8) Rod assembly
Assemble rod assembly (1) to the minimum length.
Adjust the rod assembly (8) .Length between centers of rod ends for rod assembly (8) ... 284.0 2.0 mm (11.18 0.08 inch)
Install synchronizing pin (4) in location (Z) without the spacer.Tighten synchronizing pin (4) to the following torque. ... 10 2 N m (7 1 lb ft)
Rotate fuel stop lever (7) until the fuel stop lever makes contact with the synchronizing pin (4). Fuel stop lever (7) must remain in contact with the synchronizing pin (4) during the linkage adjustment.
Illustration 3 g00606181
Adjust rod assembly (8) in order to ensure that each fuel control rod (9) is approximately positioned with the 6V-9057 Rack Synchronizing Gauge Block (10) between the trim screw and the end of the rack bar. Tighten the nuts on the rod assembly (8) in order to lock the rod assembly (8) in place.
Put 6V-9057 Rack Synchronizing Gauge (10) in position on one of the injectors. This gauge sits on the round part of the injector rack bar between the trim screw and the end of the rack bar. The gauge block should make complete contact with the trim screw and the surface of the rack bar. Note: The trim screw is provided on the injectors in order to adjust the rack's zero point. Do not adjust the trim screw. This should be done AT THE FACTORY ONLY. If a unit injector has a loose trim screw, the unit injector must be replaced with a calibrated unit injector. If a trim screw has been moved, the unit injector must be replaced with a calibrated unit injector. The fuel injector cannot be synchronized if the trim screw has been moved.
Repeat Step 5 through Step 7 for the remaining racks. If fuel control rod (9) cannot be adjusted, adjust the control housing's rod assembly (8). If the adjustment of the control housing's rod assembly (8) is necessary, all previously adjusted fuel control rods (9) must be adjusted again.
Insert the 6V-3075 Dial Indicator into location (Y). Ensure that the 5P-7263 Indicator Contact Point of the 6V-3075 Dial Indicator seats against the fuel stop lever. Use the 5P-4814 Collet Clamp in order to secure the 6V-3075 Dial Indicator in place. Place the indicator's dial on zero.
Remove synchronizing pin (4) .
Rotate governor output shaft (3) to the minimum fuel setting. Hold governor output shaft (3) in place.
Install lever (2) on governor output shaft (3) .
Illustration 4 g00609253
(A) Rod
Table 1
Tools Needed Quantity
4C-6594 Timing and Fuel Setting Tool 1
6V-9057 Rack Synchronizing Gauge 1
6V-3075 Dial Indicator 1
5P-4814 Collet Clamp 1
5P-7263 Indicator Contact Point 1
4C-6583 Governor Calibration Adapter 1
Illustration 1 g00605849
(1) Control rod assembly (2) Lever (3) Governor output shaft (4) Synchronizing pin (5) Power setting screw in hole "W" (Y) Location for the dial indicator (Z) Location for synchronizing pin
Illustration 2 g00606063
(6) Shaft (7) Fuel stop lever (8) Rod assembly
Assemble rod assembly (1) to the minimum length.
Adjust the rod assembly (8) .Length between centers of rod ends for rod assembly (8) ... 284.0 2.0 mm (11.18 0.08 inch)
Install synchronizing pin (4) in location (Z) without the spacer.Tighten synchronizing pin (4) to the following torque. ... 10 2 N m (7 1 lb ft)
Rotate fuel stop lever (7) until the fuel stop lever makes contact with the synchronizing pin (4). Fuel stop lever (7) must remain in contact with the synchronizing pin (4) during the linkage adjustment.
Illustration 3 g00606181
Adjust rod assembly (8) in order to ensure that each fuel control rod (9) is approximately positioned with the 6V-9057 Rack Synchronizing Gauge Block (10) between the trim screw and the end of the rack bar. Tighten the nuts on the rod assembly (8) in order to lock the rod assembly (8) in place.
Put 6V-9057 Rack Synchronizing Gauge (10) in position on one of the injectors. This gauge sits on the round part of the injector rack bar between the trim screw and the end of the rack bar. The gauge block should make complete contact with the trim screw and the surface of the rack bar. Note: The trim screw is provided on the injectors in order to adjust the rack's zero point. Do not adjust the trim screw. This should be done AT THE FACTORY ONLY. If a unit injector has a loose trim screw, the unit injector must be replaced with a calibrated unit injector. If a trim screw has been moved, the unit injector must be replaced with a calibrated unit injector. The fuel injector cannot be synchronized if the trim screw has been moved.
Repeat Step 5 through Step 7 for the remaining racks. If fuel control rod (9) cannot be adjusted, adjust the control housing's rod assembly (8). If the adjustment of the control housing's rod assembly (8) is necessary, all previously adjusted fuel control rods (9) must be adjusted again.
Insert the 6V-3075 Dial Indicator into location (Y). Ensure that the 5P-7263 Indicator Contact Point of the 6V-3075 Dial Indicator seats against the fuel stop lever. Use the 5P-4814 Collet Clamp in order to secure the 6V-3075 Dial Indicator in place. Place the indicator's dial on zero.
Remove synchronizing pin (4) .
Rotate governor output shaft (3) to the minimum fuel setting. Hold governor output shaft (3) in place.
Install lever (2) on governor output shaft (3) .
Illustration 4 g00609253
(A) Rod
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315B, 315C, 315D L, 320D, 320D L, 324D, 324D L, 329D, 329D L, 329D LN, 329E L, 329E LN, 988K, M312,...
1257005
SEAL-O-RING
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D MH, M325C MH
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D MH, M325C MH
1257001
SEAL-O-RING
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D MH, M325C MH
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D MH, M325C MH
1228189
SEAL
M312, M315
M312, M315
1418942
SEAL-LIP TYPE
M312, M315
M312, M315
1215978
SEAL
M312, M315
M312, M315
1390, 2590, 307C, 311D LRR, 312B L, 312C, 312D, 312E, 314D LCR, 314E LCR, 315B L, 315C, 315D L, 316E L, 317B LN, 318E L, 320 L, 320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 322 FM L, 322 LN, 322...
307C, 307D, 308C, 308D, 308E SR, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
205, 205B, 206, 206B, 211B, 212, 212B, M312, M313C, M313D, M315, M315C, M315D, M316C, M316D
5W3046
SEAL-WIPER
205, 205B, 206, 206B, 211B, 212, 212B, M312, M315
205, 205B, 206, 206B, 211B, 212, 212B, M312, M315
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D, M322D MH
533, 543, 564, 574B, HA770, HA771, HA870, HA871, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D MH, M320, M322C, M322D, M322D MH, TK370, TK371, TK...