1735575 SEAL-RING Caterpillar parts
5110B
Rating:
Alternative (cross code) number:
CA1735575
173-5575
1735575
CA1735575
173-5575
1735575
Weight: 0.010 pounds 0 kg.
MINING EXCAVATOR,
Compatible equipment models: 1735575:
Number on catalog scheme:
17
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 266-9682 White Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The installation procedure is similar for the two cylinder, the three cylinder and the four cylinder engines. The illustrations show the four cylinder engine.
Illustration 1 g00827968
Typical example
Apply Tooling (A) to the joint (9). Install the joint (9) to the base of the rocker shaft assembly (8).
Lubricate the pushrods (6) with clean engine oil. Install the pushrods (6) in the cylinder head (7). Ensure that the pushrods are installed correctly in the socket of the valve lifters. Note: If the pushrods have been used, ensure that the pushrods are installed in original positions.
Lubricate the top of the valve stems (5) with clean engine oil. Install the caps (not shown) on the top of the valve stems. Note: If the caps have been used, ensure that the caps are installed in original positions.
Lubricate the adjustment screws (3) on each rocker arm with clean engine oil before installation. Install the rocker shaft assembly (4) to the cylinder head (7). Note: Ensure that the ends of the adjustment screws on each rocker arm are correctly seated in the ends of the pushrods (6).
Install the setscrews (1) and the nuts (2).
Evenly tighten the nuts (2). Note: The tightening sequence moves from the center of the rocker shaft outward.
For C0.5 and C0.7 engines, tighten the nuts (2) to a torque of 10 N m (7.4 lb ft). For 3011C, C1.1 and C1.6 engines, tighten the nuts (2) to a torque of 23 N m (17 lb ft).For 3013C, C1.5, 3024C, C2.2, 3024CT and C2.2T engines, tighten the nuts (2) to a torque of 33 N m (24 lb ft).
Tighten the setscrews (1) to a torque of 10 N m (7.4 lb ft).
Adjust the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure to adjust the valve lash. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Install the engine oil line. Refer to Disassembly and Assembly, "Engine Oil Line- Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 266-9682 White Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The installation procedure is similar for the two cylinder, the three cylinder and the four cylinder engines. The illustrations show the four cylinder engine.
Illustration 1 g00827968
Typical example
Apply Tooling (A) to the joint (9). Install the joint (9) to the base of the rocker shaft assembly (8).
Lubricate the pushrods (6) with clean engine oil. Install the pushrods (6) in the cylinder head (7). Ensure that the pushrods are installed correctly in the socket of the valve lifters. Note: If the pushrods have been used, ensure that the pushrods are installed in original positions.
Lubricate the top of the valve stems (5) with clean engine oil. Install the caps (not shown) on the top of the valve stems. Note: If the caps have been used, ensure that the caps are installed in original positions.
Lubricate the adjustment screws (3) on each rocker arm with clean engine oil before installation. Install the rocker shaft assembly (4) to the cylinder head (7). Note: Ensure that the ends of the adjustment screws on each rocker arm are correctly seated in the ends of the pushrods (6).
Install the setscrews (1) and the nuts (2).
Evenly tighten the nuts (2). Note: The tightening sequence moves from the center of the rocker shaft outward.
For C0.5 and C0.7 engines, tighten the nuts (2) to a torque of 10 N m (7.4 lb ft). For 3011C, C1.1 and C1.6 engines, tighten the nuts (2) to a torque of 23 N m (17 lb ft).For 3013C, C1.5, 3024C, C2.2, 3024CT and C2.2T engines, tighten the nuts (2) to a torque of 33 N m (24 lb ft).
Tighten the setscrews (1) to a torque of 10 N m (7.4 lb ft).
Adjust the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure to adjust the valve lash. End By:
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Install the engine oil line. Refer to Disassembly and Assembly, "Engine Oil Line- Remove and Install".
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
12E, 140G, 143H, 14E, 14G, 16, 160H, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 16H NA, 235, 235B, 235C, 245, 24H, 3208, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B L, 3406, 3406B, 3406C, 3408, ...
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 228, 2290, 235D, 236, 2384C, 2390, 2391, ...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160K, 1...
229D, 2384C, 2484C, 24M, 3406E, 3408B, 3408C, 3412, 3412C, 3412E, 3456, 3608, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 45, 5090B, 5110B, 5...
140H, 143H, 14H, 14M, 160H, 163H, 16G, 16H, 16H NA, 16M, 173B, 24H, 24M, 3176, 3176B, 3176C, 3196, 3406B, 3406C, 3406E, 3412, 3412C, 3412D, 3412E, 3456, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L...
120H, 12H, 135H, 215B, 215C, 215D, 219D, 225, 225D, 229, 2290, 229D, 231D, 2390, 2391, 2491, 307, 312C, 312D, 315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 32...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
16G, 16H NA, 24H, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 5080, 5110B, 578, 583R, 583T, 587R, 587T, 589, 621B, 62...
245B, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3516, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5080, 5090B, 5...
24H, 3408E, 3412E, 5110B, 631D, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 69D, 769C, 769D, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 834B, 836, 844, 988B, 988F II, 990, 990 II, 992C, AD40, AD45, AE...
184, 3606, 3608, 3612, 3616, 5110B, 5230, 5230B, 578, 583R, 583T, 621K, 623K, 623K LRC, 627K, 627K LRC, 834, 844H, 844K, 950K, 962K, 966K, 972K, 980K, 990H, 990K, 992, 993K, C280-12, C280-16, C280-6, ...
2017591
SEAL AS
5110B
5110B
1270205
SEAL
5110B
5110B
5110B, CB-414, D10N, D10R, D10T, D10T2
2122827
SEAL
5110B
5110B
9X7702
SEAL-LIP TYPE
24H, 24M, 5110B
24H, 24M, 5110B
1545221
SEAL-V-RING
5110B
5110B
1968088
SEAL
365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2059743
SEAL
385B, 5090B
385B, 5090B
330D, 330D FM, 330D L, 330D LN, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, M330D,...
1565080
SEAL
322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, M325B, W330B, W345B II
322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, M325B, W330B, W345B II
9X7701
SEAL-LIP TYPE
5110B
5110B
5110B