1870565 SEAL-V-RING Caterpillar parts
988G, 988H
Rating:
Alternative (cross code) number:
CA1870565
187-0565
1870565
CA1870565
187-0565
1870565
Weight: 0.34 pounds 0 kg.
Information:
INSTALLED WIDTH
16
mm
MAXIMUM CONTACT DIAMETER
342
mm
MAXIMUM RPM
100
MAXIMUM SHAFT OD
308
mm
MINIMUM CONTACT DIAMETER
332
mm
MINIMUM SHAFT OD
308
mm
MATERIAL
Rubber
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IRWIN Tools 1870565 Impact Performance Series Concrete Screw Installation 5/32-Inch X 4-Inch Drill Bit for 3/16-Inch Screws
IRWIN Built for maximum durability and long life with impact drivers || Innovative pressed carbide tip with aggressive cutting angles for faster drilling and longer bit life || One-piece construction withstands higher torque loads than standard quick-change bits || Black oxide finish resists corrosion and increases life of bit
IRWIN Built for maximum durability and long life with impact drivers || Innovative pressed carbide tip with aggressive cutting angles for faster drilling and longer bit life || One-piece construction withstands higher torque loads than standard quick-change bits || Black oxide finish resists corrosion and increases life of bit
1899704 1751493 1870565 BK3Q2A451FC BK3Q2A451FB BK3Q2A451FA Brake Booster Vacuum Pump，Compatible With TRANSIT Bus 2.2 Accessories
AFJQENJU Low noise operation: With special structural design and noise reduction technology, the noise during operation is extremely low, creating a quiet and comfortable driving environment for drivers || High adaptability: able to work normally in various harsh environments such as high temperature, low temperature, and high altitude, with a wide range of applications || Quick Start: Start quickly without waiting, providing braking assistance immediately upon vehicle start-up to ensure driving safety || Good compatibility: Perfectly compatible with various braking systems, whether it is traditional braking systems or advanced electronic braking systems，Easy maintenance: Reasonable structural design, simple and convenient maintenance, saving time and labor costs || 1899704 1751493 1870565 BK3Q2A451FC BK3Q2A451FB BK3Q2A451FA Brake Booster Vacuum Pump，Compatible With TRANSIT Bus 2.2 Accessories
AFJQENJU Low noise operation: With special structural design and noise reduction technology, the noise during operation is extremely low, creating a quiet and comfortable driving environment for drivers || High adaptability: able to work normally in various harsh environments such as high temperature, low temperature, and high altitude, with a wide range of applications || Quick Start: Start quickly without waiting, providing braking assistance immediately upon vehicle start-up to ensure driving safety || Good compatibility: Perfectly compatible with various braking systems, whether it is traditional braking systems or advanced electronic braking systems，Easy maintenance: Reasonable structural design, simple and convenient maintenance, saving time and labor costs || 1899704 1751493 1870565 BK3Q2A451FC BK3Q2A451FB BK3Q2A451FA Brake Booster Vacuum Pump，Compatible With TRANSIT Bus 2.2 Accessories
IRWIN Tools 1870565 Impact Performance Series Concrete Screw Installation 5/32-Inch X 4-Inch Drill Bit for 3/16-Inch Screws
IRWIN Built for maximum durability and long life with impact drivers || Innovative pressed carbide tip with aggressive cutting angles for faster drilling and longer bit life || One-piece construction withstands higher torque loads than standard quick-change bits || Black oxide finish resists corrosion and increases life of bit
IRWIN Built for maximum durability and long life with impact drivers || Innovative pressed carbide tip with aggressive cutting angles for faster drilling and longer bit life || One-piece construction withstands higher torque loads than standard quick-change bits || Black oxide finish resists corrosion and increases life of bit
This part in 2 request:
Show.
This information for suppliers only!
2021-05-19
2016-10-31
Number on catalog scheme:
26
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 256-4866
or
256-4871 Seal Installer 1 Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01041799
Remove bolts (7) and nuts (6) from front housing (3) .
Install Tooling (A) before removing front housing (3) from cylinder block (1) .
Remove front housing (3) from the front of cylinder block (1) .Note: Ensure that mechanical stop lever (2) is in the full clockwise position before removing the front housing from cylinder block (1) .Note: Locating hole (4) and locating pin (5) must align for installation.
Remove gasket material from the cylinder block and remove gasket material from front housing (3) .
Inspect front housing (3) for wear or damage. If the front housing is damaged, use a new part for replacement.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 256-4866
or
256-4871 Seal Installer 1 Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01041799
Remove bolts (7) and nuts (6) from front housing (3) .
Install Tooling (A) before removing front housing (3) from cylinder block (1) .
Remove front housing (3) from the front of cylinder block (1) .Note: Ensure that mechanical stop lever (2) is in the full clockwise position before removing the front housing from cylinder block (1) .Note: Locating hole (4) and locating pin (5) must align for installation.
Remove gasket material from the cylinder block and remove gasket material from front housing (3) .
Inspect front housing (3) for wear or damage. If the front housing is damaged, use a new part for replacement.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 986H, 988F II, 988G, 98...
824, 824B, 825B, 825C, 826B, 826C, 834, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 986H, 988, 988B, 988F, 988F II, 988G, 988H, 988K, 992, R1300, R1300G, R1300G II, R2900, R2900G, R3000H
834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
322B L, 325 L, 325 LN, 325B, 325B L, 988G, 988H, 988K, OEMS
988G, R1700G
988G, 988H, D11R, R1600G
988G, 988H, 988K, D11R, D11T, R1600G, R1600H
988G, 988H
69D, 768B, 768C, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 834B, 834G, 834H, 834K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, AD55, AD55B, AD60, R2900G, R3000H
797, 834G, 834H, 836G, 836H, 844K, 854K, 988G, 988H, 990K, 992K, 993K, D10T, D10T2, D8T, D9T
988G, 988H, 988K, 993K, D11R, D11T, R1600G, R1600H
988G, 988H, 988K, 993K, D11R, D11T, R1600G, R1600H
988G, 988H
345B L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 950K, 962K, 988G, 988H, 988K, P115, R3000H, S...
988G, 988H
365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 789D, 793D, 988G, AP-1055B, BG-2455C, CB-54, CB-64, CP-573E, CP-64, CP-663E, CP-74B, CP-76, CS-531, CS-531C, CS-533C, CS-563C, CS-573C, CS-573D, CS-583C...
988G, 988H, 988K, 993K, D11R, D11T, R1600G, R1600H
988G, 988H, 988K, 993K, D11R, D11T, R1600G, R1600H
1887200
SEAL
966G II, 972G II
966G II, 972G II
3144132
SEAL GP-DUO-CONE
994D, 994F, 994H
994D, 994F, 994H
784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 994D, 994F, 994H
1750103
SEAL-RECTANGULAR
994D, 994F, 994H
994D, 994F, 994H
1750100
SEAL-RECTANGULAR
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 994D, 994F, 994H
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 994D, 994F, 994H
1098063
SEAL-O-RING
325 L, 784B, 785B, 785C, 789B, 789C, 793B, 793C, 994D
325 L, 784B, 785B, 785C, 789B, 789C, 793B, 793C, 994D