1923007 SEAL KIT- Caterpillar parts
Rating:
Alternative (cross code) number:
CA1923007
192-3007
1923007
CA1923007
192-3007
1923007
Weight: 2 pounds 0 kg.
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$53.50
18 Oct 2021
US: Empire Rigging
FLUKE MINIGRABBER Patch Cord (White) 1923007 (3781-48-9)
Pomona
Pomona
$71.07
23 Nov 2021
0.7054[0.32] Pounds
US: IronDT
2442070 Kit-Seal-H Cylinder Fits Caterpillar 1923007
TCP Warranty
TCP Warranty
For full view, you need register
Information:
Connectors for the Electronic Control Module (ECM)
Illustration 1 g03838852
Locations of the connectors on the engine ECM
(1) J1 ECM connector
(2) J2 ECM connector The Electronic Control Module (ECM) uses connectors that have 86 terminals to interface to the wiring harness.The Electronic Control Module (ECM) uses connectors that have 64 terminals to interface to the wiring harness.
Illustration 2 g01746473
Layout of the Connector Pins (view from the rear)
Removal and Installation of the Harness Connector Terminals
Terminal Removal
Table 1
Required Tools
Tool Part Number Part Description Qty
A 266-1683 Removal Tool 1
Illustration 3 g01784793
Removal of Terminal Position Assurance Components
Remove the connector from the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Use a screwdriver that has a flat blade (1) to remove the two terminal position assurance components (2) from the connector (3). Note: Do not use Tooling (A) to remove the Terminal Position Assurance components.
Illustration 4 g01784822
Removal Tool
Insert the Tooling (A) into the hole that is adjacent to the terminal in order to release the locking device. Note: Make sure that the tool stays perpendicular to the face of the connector.
Hold the tool in position and gently pull the wire in order to remove the terminal from the rear of the connector (3).
Remove the Tooling (A) from the face of the connector (3). Note: If a terminal must be replaced, part number 267-9572 must be used.Terminal Insertion
Push the terminal into the rear of the connector (3) until the terminal engages with the locking device.
Gently pull on the wire in order to make sure that the terminal is retained by the locking device.
Install the two terminal position assurance components (2) into the sides of the connector (3).
Connect the connector to the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install". Injector Connectors
Connectors at the valve cover
Illustration 5 g03838886Sensor Connectors
Analog Sensor Connector (active)
Illustration 6 g01240891Analog Sensor Connector (passive)
Illustration 7 g01241538Connectors for the Termination Resistor
Illustration 8 g01355248Engine Speed/Timing Connector
Illustration 9 g01155187Ampseal Connector (typical)
Illustration 1 g03838852
Locations of the connectors on the engine ECM
(1) J1 ECM connector
(2) J2 ECM connector The Electronic Control Module (ECM) uses connectors that have 86 terminals to interface to the wiring harness.The Electronic Control Module (ECM) uses connectors that have 64 terminals to interface to the wiring harness.
Illustration 2 g01746473
Layout of the Connector Pins (view from the rear)
Removal and Installation of the Harness Connector Terminals
Terminal Removal
Table 1
Required Tools
Tool Part Number Part Description Qty
A 266-1683 Removal Tool 1
Illustration 3 g01784793
Removal of Terminal Position Assurance Components
Remove the connector from the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Use a screwdriver that has a flat blade (1) to remove the two terminal position assurance components (2) from the connector (3). Note: Do not use Tooling (A) to remove the Terminal Position Assurance components.
Illustration 4 g01784822
Removal Tool
Insert the Tooling (A) into the hole that is adjacent to the terminal in order to release the locking device. Note: Make sure that the tool stays perpendicular to the face of the connector.
Hold the tool in position and gently pull the wire in order to remove the terminal from the rear of the connector (3).
Remove the Tooling (A) from the face of the connector (3). Note: If a terminal must be replaced, part number 267-9572 must be used.Terminal Insertion
Push the terminal into the rear of the connector (3) until the terminal engages with the locking device.
Gently pull on the wire in order to make sure that the terminal is retained by the locking device.
Install the two terminal position assurance components (2) into the sides of the connector (3).
Connect the connector to the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install". Injector Connectors
Connectors at the valve cover
Illustration 5 g03838886Sensor Connectors
Analog Sensor Connector (active)
Illustration 6 g01240891Analog Sensor Connector (passive)
Illustration 7 g01241538Connectors for the Termination Resistor
Illustration 8 g01355248Engine Speed/Timing Connector
Illustration 9 g01155187Ampseal Connector (typical)
Parts seal Caterpillar catalog:
1923006
SEAL KIT-
Caterpillar
Caterpillar
1923005
SEAL KIT-
Caterpillar
Caterpillar
Caterpillar
1923003
SEAL KIT-
Caterpillar
Caterpillar
1921437
SEAL ASSEMBLY
Caterpillar
Caterpillar
1921423
SEAL ASSEMBLY
Caterpillar
Caterpillar
1926516
SEAL - HOOD
Caterpillar
Caterpillar
1926313
SEAL
Caterpillar
Caterpillar
1923876
SEAL AS-
Caterpillar
Caterpillar
1923010
SEAL KIT-
Caterpillar
Caterpillar
Caterpillar
Caterpillar