1948364 SEAL-U-CUP Caterpillar parts
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
Rating:
Alternative (cross code) number:
CA1948364
194-8364
1948364
CA1948364
194-8364
1948364
Weight: 0.06 pounds 0 kg.
Information:
GROOVE AXIAL WIDTH
7.5
mm
GROOVE DIAMETER
120
mm
MATERIAL
Urethane Rubber - 90 Duro
ROD DIAMETER
105
mm
TYPE
STANDARD
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$9.04
18 Jul 2021
0.1102[0.05] Pounds
US: IronDT
Caterpillar Seal (1948364) New Aftermarket by CTP
CTP
CTP
Number on catalog scheme:
3
For full view, you need register
Compatible equipment models: 1948364:
Information:
Note: Flash File and Configuration File part numbers are located at https://engines.cat.com/catconnect.Perform the following procedure in order to flash program the ECM. The ECM is flashed in order to upgrade the software. Flash programming of the ECM must also be done if the ECM has been replaced. The Cat Electronic Technician (Cat ET) contains the program WinFlash. WinFlash is used in order to load software into the ECM. The following procedure is used in order to flash software into the ECM.
ProcedureNote: This procedure is only done through the 425-6889 Cable As and not a 317-7484 Communication Adapter Gp .
Connect the 425-6889 Cable As to the laptop and 9-pin service port connector on the PLE601 harness.
Open Cat ET.
Illustration 1 g03395278
Inside "Utilities" select "Preferences" then "Modify".
Illustration 2 g03396624
Select the "Communications" tab and choose "Ethernet Direct Connection".
Illustration 3 g03396549
The drop-down under "Ethernet Direct Connection" will have multiple options based on the laptop being used. Select the option based on the laptops wired ethernet connection.
Open and use WinFlash in order to load the software.Note: Typical software installation can take up to 15 minutes, and may appear to stop at 45 percent. The flash will continue on its own. Actual flash times may vary.Note: After the flash is complete reset the preferences that were changed in Step 1.d.
ProcedureNote: This procedure is only done through the 425-6889 Cable As and not a 317-7484 Communication Adapter Gp .
Connect the 425-6889 Cable As to the laptop and 9-pin service port connector on the PLE601 harness.
Open Cat ET.
Illustration 1 g03395278
Inside "Utilities" select "Preferences" then "Modify".
Illustration 2 g03396624
Select the "Communications" tab and choose "Ethernet Direct Connection".
Illustration 3 g03396549
The drop-down under "Ethernet Direct Connection" will have multiple options based on the laptop being used. Select the option based on the laptops wired ethernet connection.
Open and use WinFlash in order to load the software.Note: Typical software installation can take up to 15 minutes, and may appear to stop at 45 percent. The flash will continue on its own. Actual flash times may vary.Note: After the flash is complete reset the preferences that were changed in Step 1.d.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 325D L, 329D, 329D L
1603509
SEAL-O-RING
330B L, 345B II, 350 L
330B L, 345B II, 350 L
2Y2236
SEAL
120B, 140B
120B, 140B
2Y2717
SEAL
120B
120B
2Y2719
SEAL SHAFT
120B
120B
2Y2718
SEAL SPACER
120B
120B
6D1531
SEAL
16
16
7Y0788
SEAL
325 LN
325 LN
8E1860
SEAL GP
325 L, 325 LN
325 L, 325 LN
8E1859
SEAL GP
325 L, 325 LN
325 L, 325 LN
6Y2269
SEAL
325 L, 325 LN
325 L, 325 LN
8E1858
SEAL GP-DUO CONE
325 L, 325 LN
325 L, 325 LN
1368492
SEAL
350 L
350 L