1948366 SEAL KIT Caterpillar parts
325C L
Rating:
Alternative (cross code) number:
CA1948366
194-8366
1948366
CA1948366
194-8366
1948366
Weight: 0.79 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 1948366:
Number on catalog scheme:
None
For full view, you need register
Information:
Illustration 1 g02038981
Schematic of the "Travel Alarm" Circuit
This diagnostic code is associated with the travel alarm. The FMI 06 diagnostic code means that the Machine ECM has determined that the current is above normal.The possible causes of this failure are listed below:
The travel alarm circuit is shorted to ground.
The travel alarm has failed.
The Machine ECM has failed, but is unlikely.When this failure occurs, a warning is displayed. The travel alarm will not sound when this failure is present. Note: The following test procedure may create other failures. Ignore these created failures and clear the failures when the original failure is corrected. Test Step 1. CHECK THE TRAVEL ALARM.
Turn the disconnect switch and the key start switch to the ON position. Do NOT start the engine.
Ensure that the service code CID 0376 FMI 06 is active.
Disconnect the travel alarm from the machine harness.
Observe the status of the diagnostic code. Expected Result:The diagnostic code CID 0376 FMI 06 has changed to CID 0376 FMI 05. Results:
YES - The diagnostic code CID 0376 FMI 06 has changed to CID 0376 FMI 05. The circuit is correct. Repair: Replace the travel alarm.STOP
NO - The failure remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the travel alarm.
Disconnect the machine harness connectors J1 and J2 from the Machine ECM.
At the machine harness connector , measure the resistance from contact C2-12 of the switch panel (wire 321-BR(Brown)) to all possible source of ground. Expected Result:The resistance measurements should be greater than 5000 ohms.Results:
OK - The resistance measurements were greater than 5000 ohms. The harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is less than 5000 ohms. The harness is incorrect. The short is between the signal circuit (wire 321-BR(Brown)) and the circuit with the lowest resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all active codes.
Operate the machine.
Observe the status of the diagnostic codes. Expected Result:The diagnostic code CID 0376 FMI 06 is no longer active. Results:
YES - The diagnostic code CID 0376 FMI 06 is no longer active. The failure does not exist at this time. Repair: The initial failure was probably caused by a poor electrical connection or a short at one of the harness connections that was disconnected and reconnected. Resume normal machine operation. STOP
NO - The diagnostic code CID 0376 FMI 06 is active. The failure has not been corrected. The ECM has failed. Repair: Is unlikely that the ECM has failed. Exit this procedure and perform this CID 0376 FMI 06 procedure again. If the cause of the failure is not found, replace the ECM.STOP
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
120G, 12G, 12M, 130G, 140M, 14E, 14G, 153, 16, 160M, 163, 1693, 16G, 173B, 183B, 215, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 312B L, 315B L, 317B LN...
305.5D, 305.5E, 305C CR, 307, 307B, 307C, 308C, 308D, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312E, 312E L, 313B, 313D, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 32...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 31...
1190T, 1290T, 1390, 231D, 2391, 2491, 2590, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 320D, 3...
308D, 308E, 308E2 CR, 311C, 312C, 312C L, 314C, 320C, 320D, 322C, 323D L, 324D, 324D L, 325C, 325C L, 325D, 325D L, 329D L, 330C, 330C L, 525C, 535C, M312, M313C, M313D, M315D 2, M317D 2
303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, ...
304, 307, 307B, 307C, 307D, 308C, 308D, 311C, 312C L, 314C, 315C, 318C, 319C, 320C, 320C FM, 321C, 322C, 322C FM, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325C L, 32...
307C, 320C, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325C L, 325D, 325D FM, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN,...
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320C, 320D, 320D L, 320D2, 320D2 L, 320E, 32...
320B, 320C, 322B, 322B L, 322B LN, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 330B, 330B L, 330C, 330...
320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 320N, 321C, ...
320B, 320B L, 320C, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 325C L
1948363
SEAL KIT
325C L
325C L
2083681
SEAL O-RING
345B L
345B L
330B, 330B L
0951371
SEAL
350 L
350 L
5300P219
SEAL
325B L
325B L
218P40066
SEAL
325B L
325B L
2251782
SEAL KIT
330C L
330C L
2251783
SEAL KIT
330C L
330C L
5G3144
SEAL
330C L
330C L
375
1729733
SEAL
375
375
2043697
SEAL KIT
325C L
325C L