1G6619 SEAL-QUAD RING Caterpillar parts
AP-1000, AP-1050
Rating:
Alternative (cross code) number:
CA1G6619
1G-6619
1G6619
CA1G6619
1G-6619
1G6619
Weight: 0.01 pounds 0 kg.
ASPHALT PAVER,
Number on catalog scheme:
29
For full view, you need register
Information:
Receiver Firmware Upgrade
Preliminary Preparation
Use a computer to copy the required files to the root directory of a data card. There are two types of firmware upgrade files. These files are listed below:MS9xx loader files - MSMONnnn.s (where nnn is the version number). This file contains information for the GPS receiver.Application upgrade files - AAAAA nnn.S: AAAAA is the unit type, and nnn is the version number. Observe the following items when performing a loader upgrade:
Disconnect the machine radio from the harness before the loader upgrade begins.
Disconnect the AS400C from the harness before the upgrade begins.
Do not connect or disconnect a device from the harness once the upgrade has started. Disconnecting a device after the loader starts is more likely to cause a failure than leaving the device on the harness.
Ensure that power to the system is not lost during the upgrade.Do not upgrade the loader firmware unless the diagnostics report indicates that the loader is out of date.Upgrade Firmware Option
Ensure that a data card is inserted in the Display. Ensure that the receiver application upgrade file, named MS990xxx.s, is in the root directory of the card.
Start the Display in Service Mode. Press the "OK" key while pressing the Power key. The "Setup Menu - Configuration" dialog appears.
Press the "Installation" soft key. The "Setup Menu - Installation" screen appears.
Illustration 2 g01811395
Scroll to the "Upgrade Firmware" option. Use the arrow keys (9) .
Illustration 3 g01363424
Press the "OK" key (10). The Display and the root directory of the data card are searched.If at least one device on the CAN bus is detected, then a dialog similar to the one shown in Illustration 3 appears. All of the correctly named *.s files that are applicable for the installed CAN devices are displayed. The version of each file is also shown.
Scroll to the "MS9xx" file. Use the arrow keys.
Press the OK key (10). A screen that shows the name of the device appears. The current version of the application and the loader are also shown.
Illustration 4 g01363446
Press the "OK" key. The AccuGrade System sends the *.s file to the system. The status information is provided. A dialog that is similar to Illustration 4 appears. The dialog contains a status bar. This bar indicates the progress of the firmware upgrade. Note: Do not remove the data card or turn off the Display during the firmware upgrade.If the upgrade is successful, the version of the device is updated to reflect the change.If the upgrade is unsuccessful, the message in Illustration 5 appears.
Illustration 5 g01363647
Press the OK key.
Press the Escape key (5) two times. The "Setup Menu - Installation" screen.
Press the Escape key (5). A guidance screen appears.Slope Sensor Upgrade
The CAN device firmware files allow you to upgrade the Slope sensor for the AccuGrade System to the current firmware version. In order to complete the upgrade, use the Display. The firmware file for the sensor is available on the AccuGrade System software CD in the "CAN Device Firmware" folder. For the latest version, download the firmware that is found on
Preliminary Preparation
Use a computer to copy the required files to the root directory of a data card. There are two types of firmware upgrade files. These files are listed below:MS9xx loader files - MSMONnnn.s (where nnn is the version number). This file contains information for the GPS receiver.Application upgrade files - AAAAA nnn.S: AAAAA is the unit type, and nnn is the version number. Observe the following items when performing a loader upgrade:
Disconnect the machine radio from the harness before the loader upgrade begins.
Disconnect the AS400C from the harness before the upgrade begins.
Do not connect or disconnect a device from the harness once the upgrade has started. Disconnecting a device after the loader starts is more likely to cause a failure than leaving the device on the harness.
Ensure that power to the system is not lost during the upgrade.Do not upgrade the loader firmware unless the diagnostics report indicates that the loader is out of date.Upgrade Firmware Option
Ensure that a data card is inserted in the Display. Ensure that the receiver application upgrade file, named MS990xxx.s, is in the root directory of the card.
Start the Display in Service Mode. Press the "OK" key while pressing the Power key. The "Setup Menu - Configuration" dialog appears.
Press the "Installation" soft key. The "Setup Menu - Installation" screen appears.
Illustration 2 g01811395
Scroll to the "Upgrade Firmware" option. Use the arrow keys (9) .
Illustration 3 g01363424
Press the "OK" key (10). The Display and the root directory of the data card are searched.If at least one device on the CAN bus is detected, then a dialog similar to the one shown in Illustration 3 appears. All of the correctly named *.s files that are applicable for the installed CAN devices are displayed. The version of each file is also shown.
Scroll to the "MS9xx" file. Use the arrow keys.
Press the OK key (10). A screen that shows the name of the device appears. The current version of the application and the loader are also shown.
Illustration 4 g01363446
Press the "OK" key. The AccuGrade System sends the *.s file to the system. The status information is provided. A dialog that is similar to Illustration 4 appears. The dialog contains a status bar. This bar indicates the progress of the firmware upgrade. Note: Do not remove the data card or turn off the Display during the firmware upgrade.If the upgrade is successful, the version of the device is updated to reflect the change.If the upgrade is unsuccessful, the message in Illustration 5 appears.
Illustration 5 g01363647
Press the OK key.
Press the Escape key (5) two times. The "Setup Menu - Installation" screen.
Press the Escape key (5). A guidance screen appears.Slope Sensor Upgrade
The CAN device firmware files allow you to upgrade the Slope sensor for the AccuGrade System to the current firmware version. In order to complete the upgrade, use the Display. The firmware file for the sensor is available on the AccuGrade System software CD in the "CAN Device Firmware" folder. For the latest version, download the firmware that is found on
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
1140, 1145, 1150, 1160, 120G, 12G, 140, 141, 14G, 153, 163, 1673C, 1674, 16G, 173B, 183B, 191, 205B, 214B, 215, 215B, 215D, 216, 224B, 225, 225D, 228, 229, 229D, 231D, 235, 235B, 236, 236D, 242D, 245,...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H NA, 16H ...
214B, 224B, 3116, 3176, 3176B, 320 L, 325, 75, 950F, AP-1000, AP-1050, CP-563, E240C
120H, 120H ES, 120H NA, 135H, 135H NA, 211B, 214B, 3114, 3116, 3126, 3208, 320B, 322, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325B, 325B L, 3406E, 3408B, 3412E, 3456, 35, 3508, 3508B, 3512, 3512B,...
206B, 211B, 214B, 3114, 3116, 3126, 325, 446B, 45, 613C II, 918F, 924F, 950F, 950F II, 950G, 960F, 962G, 963B, AP-1000, AP-1050, C140-16, CD-54, CS-583, D5M, D7E, D7E LGP, E200B, E240C, G3606, G3608, ...
1090, 1140, 1145, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390,...
120B, 120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215, 215B, 215C,...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 160K, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 32...
24M, 30/30, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 583T, 587T, 621B, 621F, 621G, 621H, 623E, 623F, 623G, 623H, 627F,...
10 FT, 10-20B, 1090, 1190, 1190T, 120G, 128, 129, 12E, 12F, 12G, 130G, 1390, 140G, 14E, 14G, 14H, 14H NA, 153, 16, 160G, 163, 16G, 16H, 16H NA, 172, 173B, 183, 183B, 184, 191, 215, 225, 225D, 227, 229...
120H, 120M, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140M 2, 140M 3, 140M 3 AWD, 14H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16G, 16H, 16H NA, 215, 216, 216B, 219D, 225, 226B, 227, 228, 232B, 2...
10 FT, 10-20B, 120H, 216, 228, 236, 245, 248, 24H, 267, 311F LRR, 3126, 3126B, 3126E, 3208, 3408E, 3412E, 3616, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 420E, 428F, 430E, 432E, 43...
1G6612
SEAL-BACKUP
AP-1000, AP-1050
AP-1000, AP-1050
1G6613
SEAL-BACKUP
AP-1050
AP-1050
1G6611
SEAL-O-RING
AP-1050
AP-1050
1G6558
SEAL-RING
AP-1050
AP-1050
1G6618
SEAL-RING
AP-1050
AP-1050
1G6617
SEAL-O-RING
AP-1050
AP-1050
8C7465
SEAL
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1200, AP-650B, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1200, AP-650B, AP-800, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C
AP-1000, AP-1050
7R3094
SEAL
AP-1000, AP-1050
AP-1000, AP-1050
1G6616
SEAL-O-RING
AP-1050
AP-1050
1G6615
SEAL-BACKUP
AP-1050
AP-1050
1G6614
SEAL-QUAD RING
AP-1050
AP-1050