1P9261 SEAL-RING Caterpillar parts
14G, 14H, 14H NA, 16G, 16H, 16H NA, 24H, 24M, 55, 589, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637E, 637G, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, ...
Rating:
Alternative (cross code) number:
CA1P9261
1P-9261
1P9261
CA1P9261
1P-9261
1P9261
Weight: 0.01 pounds 0 kg.
Information:
AXIAL LIP
3.1242
mm
AXIAL WIDTH
2.3114
mm
ID
0
mm
MATERIAL
(PTFE) Plastic - Glass filled
OD
173.5582
mm
RADIAL HEIGHT
9.6012
mm
TYPE
INTERNAL
ARTICULATED TRUCK, WINCH,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
9G0286 9G0281 1P9261 8D9739 RING-SEAL Compatible With TRANSMISSION GEARBOX (8D9739)
Generic
Generic
9G0286 9G0281 1P9261 8D9739 RING-SEAL Compatible With TRANSMISSION GEARBOX (1P9261)
Generic
Generic
Compatible equipment models: 1P9261:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
C     235-0632     Cylinder Installation Tool Gp     1    
D     191-1135     Cylinder Liner Spacer As     1    
E     207-1600 (1)
or
207-1601     Rubber Lubricant     -    
F     6V-7030     Micrometer Depth Gauge Group     1    
G     147-8862     Dial Bore Gauge     1    
H     8T-0447     Dial Calipers     1    
( 1 ) EAME
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Inspect the cylinder liner. Refer to Reuse and Salvage Guidelines, "Cylinder Liners for 3600 Engines".
Illustration 1 g00575575
Use Tooling (F) in order to measure the groove depth of the gasket at four places. The depth of the groove must be 3.50 0.05 mm (0.138 0.001 inch). The depth of the groove must not vary more than 0.020 mm (0.0008 inch). Refer to Specifications, "Cylinder Liner".
Illustration 2 g00575577
Use Tooling (H) in order to measure the thickness of the cylinder liner flange at four places. The thickness of the flange must be 33.00 0.03 mm (1.299 0.001 inch). The thickness of the flange must not vary more than 0.013 mm (0.0005 inch). Refer to Specifications, "Cylinder Liner".
Illustration 3 g00575579
Use Tooling (G) in order to measure the cylinder liner's inside diameter at four locations. The cylinder liner should be measured at two points that are separated by 90 degrees at each location. Refer to Specifications, "Cylinder Liner".
Remove the rust and/or deposits from the outside surface of the cylinder liner. Use glass beads or a wire brush.
Thoroughly clean the cylinder liner bore in the cylinder block. Apply liquid soap to the sealing surfaces.
Illustration 4 g01303307
Install O-ring seal (2) and O-ring seals (3) on cylinder liner (1) .
Apply Tooling (E) or liquid soap to the O-ring seals.
Attach Tooling (C) and a suitable lifting device to the cylinder liner. The weight of the cylinder liner is approximately 100 kg (220 lb).
Carefully lower the cylinder liner into the cylinder block. Lower the cylinder liner until the lower O-ring seals of the cylinder liner enter the seal bore in the cylinder block.
Remove Tooling (C). Tap the top of the cylinder liner with a large rubber mallet in order to seat the cylinder liner in the cylinder block. Tooling (D) is also available in order to seat the cylinder liner in the cylinder block.End By: Install the piston and connecting rod. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
C     235-0632     Cylinder Installation Tool Gp     1    
D     191-1135     Cylinder Liner Spacer As     1    
E     207-1600 (1)
or
207-1601     Rubber Lubricant     -    
F     6V-7030     Micrometer Depth Gauge Group     1    
G     147-8862     Dial Bore Gauge     1    
H     8T-0447     Dial Calipers     1    
( 1 ) EAME
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Inspect the cylinder liner. Refer to Reuse and Salvage Guidelines, "Cylinder Liners for 3600 Engines".
Illustration 1 g00575575
Use Tooling (F) in order to measure the groove depth of the gasket at four places. The depth of the groove must be 3.50 0.05 mm (0.138 0.001 inch). The depth of the groove must not vary more than 0.020 mm (0.0008 inch). Refer to Specifications, "Cylinder Liner".
Illustration 2 g00575577
Use Tooling (H) in order to measure the thickness of the cylinder liner flange at four places. The thickness of the flange must be 33.00 0.03 mm (1.299 0.001 inch). The thickness of the flange must not vary more than 0.013 mm (0.0005 inch). Refer to Specifications, "Cylinder Liner".
Illustration 3 g00575579
Use Tooling (G) in order to measure the cylinder liner's inside diameter at four locations. The cylinder liner should be measured at two points that are separated by 90 degrees at each location. Refer to Specifications, "Cylinder Liner".
Remove the rust and/or deposits from the outside surface of the cylinder liner. Use glass beads or a wire brush.
Thoroughly clean the cylinder liner bore in the cylinder block. Apply liquid soap to the sealing surfaces.
Illustration 4 g01303307
Install O-ring seal (2) and O-ring seals (3) on cylinder liner (1) .
Apply Tooling (E) or liquid soap to the O-ring seals.
Attach Tooling (C) and a suitable lifting device to the cylinder liner. The weight of the cylinder liner is approximately 100 kg (220 lb).
Carefully lower the cylinder liner into the cylinder block. Lower the cylinder liner until the lower O-ring seals of the cylinder liner enter the seal bore in the cylinder block.
Remove Tooling (C). Tap the top of the cylinder liner with a large rubber mallet in order to seat the cylinder liner in the cylinder block. Tooling (D) is also available in order to seat the cylinder liner in the cylinder block.End By: Install the piston and connecting rod. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
9D6588
SEAL-LIP TYPE
16G, 16H, 16H NA, 16M
16G, 16H, 16H NA, 16M
8D3307
SEAL
16G, 16H, 16H NA, 16M
16G, 16H, 16H NA, 16M
1731007
SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1010509
SEAL-INTEGRAL
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
1659954
SEAL-LIP TYPE
24H, 24M
24H, 24M
1668815
SEAL GP-FINAL DRIVE
24H, 24M
24H, 24M
4D0907
SEAL
12G, 130G, 140, 140B, 140G, 14E, 14G, 16G
12G, 130G, 140, 140B, 140G, 14E, 14G, 16G
5F4258
SEAL
120G, 12G, 14G, 16G
120G, 12G, 14G, 16G
3G1689
SEAL KIT
14G, 16G
14G, 16G
2G5994
SEAL
14G
14G
2G5976
SEAL
16G
16G
7T5617
SEAL AS
589, D10N, D8L, D9L, D9N, D9R, D9T
589, D10N, D8L, D9L, D9N, D9R, D9T
5D1597
SEAL-O-RING
16, 589, 768C, 769C, 772, 797, 797B, 797F, 936, 936F, D35C, D35HP, D44B, D550B, D8L, D9N, D9R, G936
16, 589, 768C, 769C, 772, 797, 797B, 797F, 936, 936F, D35C, D35HP, D44B, D550B, D8L, D9N, D9R, G936
7X1551
SEAL-LIP TYPE
589, D9R, D9T
589, D9R, D9T
6Y6275
SEAL GP-DUO-CONE
589, D9R, D9T
589, D9R, D9T
5P7905
SEAL
589, 621R, 943, D10N, D8L, D9L, D9N
589, 621R, 943, D10N, D8L, D9L, D9N
8T1594
SEAL
589, D6H, D6H XL, D6H XR, D6R, D7H, D7R, D8L, D8N
589, D6H, D6H XL, D6H XR, D6R, D7H, D7R, D8L, D8N
9G0608
SEAL
589, D8L
589, D8L
6V3325
SEAL-LIP TYPE
578, 589
578, 589
3D8241
SEAL-O-RING
16, 16G, 16H, 16H NA, 589, 621, 641, 641B, 650B, 651, 651E, 657, 657B, 657E, 657G, 666, 776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785D, 824, 824B, 825B, 988, D10N, D10R, D10T, D10T2, D8L, D9L, D...
16, 16G, 16H, 16H NA, 589, 621, 641, 641B, 650B, 651, 651E, 657, 657B, 657E, 657G, 666, 776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785D, 824, 824B, 825B, 988, D10N, D10R, D10T, D10T2, D8L, D9L, D...
2H3843
SEAL-LIP TYPE
120G, 12G, 140G, 14E, 14G, 14H NA, 16, 16G, 16H NA, 578, 583R, 587R, 587T, 589, D11N, D6H, D6H XL, D6H XR, D7H, D8L, D8N, D9L, PL87
120G, 12G, 140G, 14E, 14G, 14H NA, 16, 16G, 16H NA, 578, 583R, 587R, 587T, 589, D11N, D6H, D6H XL, D6H XR, D7H, D8L, D8N, D9L, PL87