2070544 SEAL AS Caterpillar parts
1190, 1190T, 1390, 2390, 2391, 324D FM, 325C FM, 325C L, 325D FM, 325D FM LL, 521, 522, 527, 541, 963B, 963C, 963D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D6R II, D6R III, D6R STD, D6T, D6T...
Rating:
Alternative (cross code) number:
CA2070544
207-0544
2070544
CA2070544
207-0544
2070544
Weight: 0.04 pounds 0 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$8.86
12 Mar 2019
REPLACEMENT CATERPILLAR: REPLACEMENT CAT
CATERPILLAR 2070544 SEAL AS NEW
This part in 2 request:
Show.
This information for suppliers only!
2018-01-15
2017-11-24
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 2070544:
TRACK SKIDDER
527
Information:
Transmission, SPN 1079 FMI 3Conditions Which Generate This Code:
Illustration 1 g01343715
Connections of the 5 Volt Supply
The sensor supply is a power supply that is internal to the ECM. The sensor supply provides +5 DCV in order to operate the sensors.This diagnostic code will be recorded when the Transmission ECM reads the voltage for the circuit of the sensor supply as being above normal.The results of this diagnostic code are listed:
All of the associated sensors will also log diagnostic codes.The possible causes of the diagnostic code are listed:
+5 DCV (wire R997-OR(Orange)) is shorted to the +battery circuit in the machine harness.
The ECM has failed. This is unlikely.Test Step 1. CHECK FOR SHORT TO THE +BATTERY CIRCUIT
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
At the machine harness connectors for the ECM, measure the resistance between the +battery contact and the contact for the sensor supply voltage. See the schematic for more detailed information about the sensor power supply for the sensor that is being tested. Expected Result:The resistance that is measured should be greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit is correct. The ECM has failed.Repair: It is unlikely that the ECM has failed. Perform this SPN 1079 FMI 3 again. If the cause of the diagnostic code is NOT found, replace the Transmission ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance measures less than 5000 ohms. The machine harness has failed. There is a short between the +battery circuit and the circuit for the sensor power supply in the machine harness.Repair: Repair the machine harness or replace the machine harness. STOP
Illustration 1 g01343715
Connections of the 5 Volt Supply
The sensor supply is a power supply that is internal to the ECM. The sensor supply provides +5 DCV in order to operate the sensors.This diagnostic code will be recorded when the Transmission ECM reads the voltage for the circuit of the sensor supply as being above normal.The results of this diagnostic code are listed:
All of the associated sensors will also log diagnostic codes.The possible causes of the diagnostic code are listed:
+5 DCV (wire R997-OR(Orange)) is shorted to the +battery circuit in the machine harness.
The ECM has failed. This is unlikely.Test Step 1. CHECK FOR SHORT TO THE +BATTERY CIRCUIT
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
At the machine harness connectors for the ECM, measure the resistance between the +battery contact and the contact for the sensor supply voltage. See the schematic for more detailed information about the sensor power supply for the sensor that is being tested. Expected Result:The resistance that is measured should be greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit is correct. The ECM has failed.Repair: It is unlikely that the ECM has failed. Perform this SPN 1079 FMI 3 again. If the cause of the diagnostic code is NOT found, replace the Transmission ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance measures less than 5000 ohms. The machine harness has failed. There is a short between the +battery circuit and the circuit for the sensor power supply in the machine harness.Repair: Repair the machine harness or replace the machine harness. STOP
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D L, 325D MH, 326D L, 329D, 329D L, 329D LN, 32...
320C, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325B L, 325C, 325C FM, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D L, 336D...
320C, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325B L, 325C, 325C FM, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C, 330C L, 330D, 330D L, 336D...
320C, 320D, 321B, 321C, 321D LCR, 322C, 324D, 324D L, 325C, 325C L, 328D LCR, 330C L
320C, 320D, 320D L, 320E L, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L, 330C L
1390, 2590, 325B L, 325C, 325C L, 325D L, 325D MH, 330B L, 330C L, 330D, 330D L, 336D, 345B, 345B II, 345B II MH, 385B, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752, W330B, W345B II
322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336...
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
9W8877
SEAL-RING
D6R, D6R II
D6R, D6R II
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
527, 572R, 572R II, 583R, 583T, 587R, 587T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7R, D7R II, D7R XR, D8R, D8R II, D8T, D9R, D9T, PL83, PL87
527, 963, 963B, 973, D6H, D6H II, D6H XL, D6H XR, D6R, D7H, D8L, D8N, D9N, D9R
583R, D6R, D8R, D8R II, D8T, D9N, D9R
517, 527, D5HTSK II, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
D5H, D5H XL, D5R LGP, D6H, D6H XL, D6H XR, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
550, 550B, 560B, 570, 570B, 580, 580B, 611, 740, 740B, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 962G, 963, 963B, 963C, D400E II, D6M, D6N, D6R, D6R II, IT62G II
517, 527, 572R II, D5HTSK II, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR, HYDRAULIC
963C, 973, 973C, 973D, 977H, 977K, 977L, 983, 983B, D6R, D6R II, D7F, D8K
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP
1190, 1190T, 322C, 325C FM, 527, D6H, D6H XL, D6H XR, D6R, D6R II, OEMS, TK721, TK722, TK741