SEAL-O-RING 2413294 - Caterpillar

2413294 SEAL-O-RING Caterpillar parts G3512E

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2413294
241-3294
2413294

Weight: 0.28 pounds 0 kg.

Information:

CROSS SECTION DIAMETER 6.99 mm

ID 747 mm

MATERIAL Rubber

OD 0 mm

Buy SEAL-O-RING 2413294 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

#US Replacement Part Fits for Whirlpool 7GS2SHEXPL00 Refrigerator Ice Maker Control Board icepart#2413294

$131.99

08 Oct 2025

RU: ZODU-Store

#US Replacement Part Fits for Whirlpool 7GS2SHEXPL00 Refrigerator Ice Maker Control Board icepart#2413294
Generic NOTE - Package included: 1 Set ONLY. Please check all carefully (photos and model) and make sure it will compatible with your original one. || Color: Black. Color: Black || Compatible Model: 7GS2SHEXPL00 || Part Number: 7GS2SHEXPL00

#US Replacement Part for Alternator Magneto Stator Fit for Polaris Ranger 500 2X4 4x4 Carb Israel 05-09 U1#Stator2315294

$212.99

18 Dec 2024

RU: Trang-Store

#US Replacement Part for Alternator Magneto Stator Fit for Polaris Ranger 500 2X4 4x4 Carb Israel 05-09 U1#Stator2315294
Generic Manufacturer Part Number: 3089579 .NOTE - Package included: 1 Set ONLY. Please check all carefully (photos and model) and make sure it will compatible with your original one. || Part Number: 3089579

Polaris 2413294 LAMP-CNTR HI MNTD STOP Part

$199.99

17 May 2024
0.69[0.31] pounds
US: Fix_My_Toys

Polaris 2413294 LAMP-CNTR HI MNTD STOP Part
Polaris For schematic location 7 only || See product description below for vehicle fitment or to verify fitment for your specific vehicle, please contact us, and provide us with your VIN that can be found on your vehicle or your insurance

Number on catalog scheme: 2

Caterpillar 2413294 Parts scheme SEAL-O-RING

For full view, you need register

Compatible equipment models: 2413294:

GENERATOR SET G3512E Caterpillar

Information:

Image1.1.1
Image1.1.2
Image1.1.3
2. Disconnect harness-1 and harness-2 from each joystick of remote control valves.
Image1.2.1
Disconnect DT connector (6P) of harness-1 of each joystick to the console harness.
Disconnect the bullet terminals of harness-2 of the right joystick to the console harness wires (NO.320: red) and (NO.200: black).
Disconnect the bullet terminals of harness-2 of the left joystick to the console harness wires (NO.972: blue) and (NO.235: black).
Image1.3.1
Image1.3.2
3. Remove pin (1132532) and remove the old joystick grip.
Image1.4.1
4.Install each new joystick grip and install pin (1132532) to hold the grip in position.
Installation procedure is basically the reverse of the removal procedure, described above.
5.After replacing with new joystick, perform calibration of the joystick thumbwheel by using any of the two methods, calibration with the monitor or calibration with Caterpillar Electronic Technician.
Refer to the service manual "Tool Control System. Testing and Adjusting Section"