2434572 SEAL-O-RING Caterpillar parts
776D, 777D, 777F, 777G
Rating:
Alternative (cross code) number:
CA2434572
243-4572
2434572
CA2434572
243-4572
2434572
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.53
mm
DASH SIZE
274
ID
253.59
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
TRACTOR, TRUCK,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement for fits 2434572 Seal O Ring Fits Caterpillar Models
Degelo
Degelo
$13.89
18 Jan 2024
US: Florida-Parts-Z
2434572 - Seal-O-Ring fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Information:
Assembly Procedure
Table 1
Required Tools
Tooling Part Number Description Qty
A 1P-0510 Driver 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g00992235
Illustration 2 g00992236
Use Tooling (A) in order to install bearing (1) in throttle base (2).
Illustration 3 g00992239
Place seal (4) in position in the counterbore.
Use Tooling (A) in order to install retainer (3).
Turn over throttle base (2). Repeat steps 1 through 3.
Illustration 4 g00992281
Align the identification marks on the throttle base (2) and install the gasket and throttle base (2) on base assembly (5).
Illustration 5 g00992355
Install idle screw (8), the spring, and seal (7).
Turn power mixture adjustment (6) to the CENTER position between the "R" and the "L".
Illustration 6 g00992360Note: Use caution when you install the shaft. This may cause damage to the seals.
Install throttle lever (9), the lever stop, and the shaft.
Illustration 7 g00992363
Place throttle plate (10) in position on the throttle shaft. Install the screws and lockwashers that hold throttle plate (10) in position finger tight.
Use throttle lever (9) in order to turn throttle plate (10) from the CLOSED position to the OPEN position. This will position throttle plate (10) in the center of the bore. Tighten the screws and ensure that throttle lever (9) turns freely.
Illustration 8 g00992364
Place diaphragm assembly (12) in position on base assembly (5). Install spring (11) on diaphragm assembly (12).
Illustration 9 g00992366
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Place cover (13) in position on diaphragm assembly (12). Install the five bolts and lockwashers that hold cover (13) in position.
Illustration 10 g00992369
Install adapter (14) and the gasket to the throttle base. End By:
Install the carburetor. Refer to Disassembly and Assembly, "Carburetor - Install" for the engine that is being serviced.
Table 1
Required Tools
Tooling Part Number Description Qty
A 1P-0510 Driver 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g00992235
Illustration 2 g00992236
Use Tooling (A) in order to install bearing (1) in throttle base (2).
Illustration 3 g00992239
Place seal (4) in position in the counterbore.
Use Tooling (A) in order to install retainer (3).
Turn over throttle base (2). Repeat steps 1 through 3.
Illustration 4 g00992281
Align the identification marks on the throttle base (2) and install the gasket and throttle base (2) on base assembly (5).
Illustration 5 g00992355
Install idle screw (8), the spring, and seal (7).
Turn power mixture adjustment (6) to the CENTER position between the "R" and the "L".
Illustration 6 g00992360Note: Use caution when you install the shaft. This may cause damage to the seals.
Install throttle lever (9), the lever stop, and the shaft.
Illustration 7 g00992363
Place throttle plate (10) in position on the throttle shaft. Install the screws and lockwashers that hold throttle plate (10) in position finger tight.
Use throttle lever (9) in order to turn throttle plate (10) from the CLOSED position to the OPEN position. This will position throttle plate (10) in the center of the bore. Tighten the screws and ensure that throttle lever (9) turns freely.
Illustration 8 g00992364
Place diaphragm assembly (12) in position on base assembly (5). Install spring (11) on diaphragm assembly (12).
Illustration 9 g00992366
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Place cover (13) in position on diaphragm assembly (12). Install the five bolts and lockwashers that hold cover (13) in position.
Illustration 10 g00992369
Install adapter (14) and the gasket to the throttle base. End By:
Install the carburetor. Refer to Disassembly and Assembly, "Carburetor - Install" for the engine that is being serviced.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
8J9449
SEAL-RING
777, 777B, 777D
777, 777B, 777D
8J9450
SEAL-RING
777, 777B, 777D
777, 777B, 777D
8J9916
SEAL-RING
777, 777B, 777D
777, 777B, 777D
8J9933
SEAL-RING
777, 777B, 777D
777, 777B, 777D
3232197
SEAL-U-CUP
776D, 777D, 777F
776D, 777D, 777F
5P4342
SEAL-O-RING
528, 528B, 530B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
528, 528B, 530B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
7Y0640
SEAL-O-RING
365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
3654920
SEAL GP-DUO-CONE
773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G, AD55, AD55B, AD60
773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G, AD55, AD55B, AD60
9J5570
SEAL
777D, 777F
777D, 777F
1757894
SEAL-O-RING
777F
777F
3285492
SEAL
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 773F, 775F, 777F, D7E, D7E LGP
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 773F, 775F, 777F, D7E, D7E LGP
3232197
SEAL-U-CUP
776D, 777D, 777F
776D, 777D, 777F
3124253
SEAL-U-CUP
793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
1986899
SEAL-NOZZLE
793C
793C
3558930
SEAL
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797F
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797F
3481798
SEAL
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797F
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797F
3477948
SEAL
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797B, 797F
785C, 785D, 789C, 793D, 793F, 793F-XQ, 795F AC, 797B, 797F
2587206
SEAL
R1600, R1700G
R1600, R1700G
2017745
SEAL-BUFFER
R1600
R1600
1846801
SEAL
554, 564, 574, 574B, D400E II
554, 564, 574, 574B, D400E II
1959771
SEAL-O-RING
730, 730C, 740, 740B, D400E II, M325C MH, M325D L MH, M325D MH
730, 730C, 740, 740B, D400E II, M325C MH, M325D L MH, M325D MH
1959769
SEAL-O-RING
740, 740B, D400E II
740, 740B, D400E II
1704949
SEAL
730, 730C, 740, 740B, D400E II
730, 730C, 740, 740B, D400E II