2667964 SEAL-O-RING Caterpillar parts
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
Rating:
Alternative (cross code) number:
CA2667964
266-7964
2667964
CA2667964
266-7964
2667964
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.5
mm
ID
29.7
mm
MATERIAL
RUBBER
OD
0
mm
EXCAVATOR,
Compatible equipment models: 2667964:
Number on catalog scheme:
7
For full view, you need register
Information:
Personal injury or death can result from sudden machine movement.Sudden movement of the machine or release of air pressure or oil pressure can cause injury to persons on or near the machine.To help prevent possible injury before testing and adjusting any air system or hydraulic system, perform the procedure in the Testing and Adjusting, "General Information" section.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00462941
Automatic lubrication injector (1) Adjusting screw (2) Locknut (3) Threaded plug for the adjusting screw (4) Piston assembly (5) Discharge chamberThe amount of lubricant that is supplied to the bearing is determined by the volume of lubricant in discharge chamber (5). This volume is controlled by the setting of adjusting screw (1). Adjusting screw (1) controls the travel of piston assembly (4). When you turn adjusting screw (1) clockwise, the amount of lubricant that is injected decreases. When you turn adjusting screw (1) counterclockwise, the amount of lubricant that is injected increases.Note: One 360 degree turn of the adjusting screw is equal to approximately 0.10 cc (.006 cubic inch) of lubricant.Movement of piston assembly (4) indicates that the automatic lubrication injector is working. When the injector discharges lubricant, piston assembly (4) moves into threaded plug (3) for adjusting screw (1). When discharge chamber (5) is filling with lubricant, piston assembly (4) moves back out of the threaded plug for adjusting screw (1) until piston assembly (4) rests against the end of adjusting screw (1) .Adjustment
Pressurized lubricant can cause personal injury. During injection, the lube lines are pressurized to 17 000 kPa (2500 psi).To avoid possible injury, make sure that the lines are not pressurized before adjusting the lube injectors.
If an automatic lubrication injector has been repaired or an injector has been replaced, proper adjustment of the measuring chamber is required. Proper adjustment of adjusting screw (1) and the measuring chamber will depend on the bearing that is being lubricated.Note: Turn adjusting screw (1) by hand. Do not use wrenches.
Remove the cap that covers adjusting screw (1) and loosen locknut (2) .
Turn adjusting screw (1) clockwise into threaded plug (3) for the adjusting screw. Continue turning until the adjustment screw is finger tight.
Turn adjusting screw (1) counterclockwise to the specified number of turns.Note: For the specified settings of adjusting screw (1), refer to the following section in this Service Manual, "Lubrication Injector Banks - Adjust".
Tighten locknut (2) and replace the cap.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
320C, 322C
2742502
SEAL-O-RING
320C, 322C
320C, 322C
320C, 322C
320C, 322C
320C, 322C
320C, 322C
1390, 2590, 325B L, 325C, 325C L, 325D L, 325D MH, 330B L, 330C L, 330D, 330D L, 336D, 345B, 345B II, 345B II MH, 385B, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752, W330B, W345B II
834G, 834H, TK1051
1672334
SEAL-U-CUP
834G, 834H, TK1051
834G, 834H, TK1051
2226716
SEAL
TK1051
TK1051
2667965
SEAL-O-RING
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
2667963
SEAL-O-RING
320C, 322C, 325C
320C, 322C, 325C