SEAL-O-RING 3107258 - Caterpillar

Cross-Reference Information for Diagnostic Codes
Table 1 is a list of the diagnostic codes for the engine. The diagnostic codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.Further explanations of diagnostic codes are explained after Table 1.Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Table 1
Cross-Reference from Diagnostic Trouble Codes to Troubleshooting Procedure
J1939 Code and Description Troubleshooting Procedure
95-2 Engine Fuel Filter Differential Pressure : Erratic, Intermittent, or Incorrect The filtered fuel pressure is greater than the unfiltered fuel pressure. Ensure that the sensor connectors are connected to the correct sensors. If an electrical problem with a sensor is suspected, refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for information that is related to troubleshooting an electrical problem with the fuel pressure sensors.
99-2 Engine Oil Filter Differential Pressure : Erratic, Intermittent, or Incorrect The filtered oil pressure is greater than the unfiltered oil pressure. Ensure that the sensor connectors are connected to the correct sensors. If an electrical problem with a sensor is suspected, refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test" for information that is related to troubleshooting an electrical problem with the oil pressure sensors.
100-3 Engine Oil Pressure : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
100-4 Engine Oil Pressure : Voltage Below Normal
101-3 Engine Crankcase Pressure : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
101-4 Engine Crankcase Pressure : Voltage Below Normal
101-13 Engine Crankcase Pressure : Out of Calibration Troubleshooting, "Sensor Calibration Required - Test"
105-3 Engine Intake Manifold 1 Temperature : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
105-4 Engine Intake Manifold 1 Temperature : Voltage Below Normal
108-3 Barometric Pressure : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Active) - Test"
108-4 Turbocharger Outlet Pressure Sensor voltage above normal
110-3 Engine Coolant Temperature : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
110-4 Engine Coolant Temperature : Voltage Below Normal
168-3 Battery Potential / Power Input #1 : Voltage Above Normal Troubleshooting, "Electrical Power Supply - Test"
168-4 Battery Potential / Power Input #1 : Voltage Below Normal
172-3 Engine Air Inlet Temperature : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
172-4 Engine Air Inlet Temperature : Voltage Below Normal
175-3 Engine Oil Temperature 1 : Voltage Above Normal Troubleshooting, "Sensor Signal (Analog, Passive) - Test"
175-4 Engine Oil Temperature 1 : Voltage Below Normal
190-8 Engine Speed : Abnormal Frequency, Pulse Width, or Period Troubleshooting, "Speed/Timing - Test"
630-2 Calibration Memory : Erratic, Intermittent, or Incorrect Troubleshooting, "Configuration Parameters"
631-2 Calibration Module : Erratic, Intermittent, or Incorrect Troubleshooting, "ECM Software - Install"
651-5 Engine Injector Cylinder #01 : Current Below Normal Troubleshooting, "Injector Solenoid - Test"
651-6 Engine Injector Cylinder #01 : Current Above Normal
652-5 Engine