3360411 SEAL-LIP TYPE Caterpillar parts
797B
Rating:
Alternative (cross code) number:
CA3360411
336-0411
3360411
CA3360411
336-0411
3360411
Weight: 0.15 pounds 0 kg.
TRUCK,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$21.61
02 Jun 2021
0.02[0.01] Pounds
US: PartsHawk
Redhorse Performance 336-04-11 Inverted Flare Fitting, 1 Pack
Red Horse Performance Superior strength || Leak proof performance || High quality
Red Horse Performance Superior strength || Leak proof performance || High quality
Number on catalog scheme:
87
For full view, you need register
Compatible equipment models: 3360411:
Information:
Track Carrier Roller Lubrication
TRACK CARRIER ROLLER
1. Shaft. 2. Duo-Cone seals. 3. Passage. 4. Cover. 5. Bearings. 6. Plug.If lubricant is added with the roller removed from the machine, shaft (1) must be in a horizontal position.Lubricant is sent into center passage (3) through the 5M2080 Nozzle. The lubricant fills the cavity between shaft (1) and the roller. When the cavity is full, the pressure of the oil causes the air and extra lubricant to go out the relief threads in the nozzle.When the lubricant does not have any bubbles, remove the nozzle and install the plug. Tighten the plug to a torque of 125 15 lb.ft. (17.3 2.1 mkg).Track Rollers
The track rollers are fastened to the track roller frames. The track rollers are in contact with the inside surfaces of the track links. Flanges on the track rollers prevent the movement of the track from side to side. The inside surfaces of the track links cause an equal distribution of the weight of the machine along the track.Each track roller frame has seven track rollers, three single flange and four double flange. The installation of the track rollers is as follows: 1. Start at the front of the machine and install two double flange rollers. 2. Then install two single flange rollers. 3. Then install two double flange rollers. 4. Install one single flange roller next to the final drive sprocket.
TRACK ROLLER
1. Pin. 2. Inner end collar. 3. Bearings. 4. Outer end collar. 5. Shaft. 6. Duo-Cone seals. 7. Track roller.The flange at the center of shaft (5) gets the side load on the roller. Bearings (3) also get the side load on the roller. The amount of side movement or end clearance of the shaft can not be adjusted.The track rollers have Duo-Cone floating seals (6) at both ends of shaft (5).Track Roller Lubrication
TRACK ROLLER
1. Shaft. 2. Duo-Cone seals. 3. Plug. 4. Reservoirs. 5. Center passage.If lubricant is added with the roller removed from the machine, shaft (1) must be in a horizontal position. The slot, in the end where the 5M2080 Nozzle is installed, must be down.Lubricant is sent into center passage (5) through the 5M2080 Nozzle. The lubricant fills the reservoirs (4) in the rollers. When the reservoirs are full, the pressure of the oil causes the air and extra lubricant to go out the relief threads in the nozzle.When the lubricant does not have any bubbles, remove the nozzle and install the plug. Tighten the plug to a torque of 125 15 lb.ft. (17.3 2.1 mkg).Front Idlers
The front idlers put the tracks in position in front of the track rollers. They also keep the tracks in alignment with the sprockets.The adjustment of the tracks is done by the movement of the front idlers. The track adjusters move the front idlers and hold them in position.
FRONT IDLER
1. Bearing. 2. Bushing assemblies (two). 3. Duo-Cone seals (two). 4. Bearing. 5. Shaft. 6. End collars (two).The position of the front idlers is controlled
TRACK CARRIER ROLLER
1. Shaft. 2. Duo-Cone seals. 3. Passage. 4. Cover. 5. Bearings. 6. Plug.If lubricant is added with the roller removed from the machine, shaft (1) must be in a horizontal position.Lubricant is sent into center passage (3) through the 5M2080 Nozzle. The lubricant fills the cavity between shaft (1) and the roller. When the cavity is full, the pressure of the oil causes the air and extra lubricant to go out the relief threads in the nozzle.When the lubricant does not have any bubbles, remove the nozzle and install the plug. Tighten the plug to a torque of 125 15 lb.ft. (17.3 2.1 mkg).Track Rollers
The track rollers are fastened to the track roller frames. The track rollers are in contact with the inside surfaces of the track links. Flanges on the track rollers prevent the movement of the track from side to side. The inside surfaces of the track links cause an equal distribution of the weight of the machine along the track.Each track roller frame has seven track rollers, three single flange and four double flange. The installation of the track rollers is as follows: 1. Start at the front of the machine and install two double flange rollers. 2. Then install two single flange rollers. 3. Then install two double flange rollers. 4. Install one single flange roller next to the final drive sprocket.
TRACK ROLLER
1. Pin. 2. Inner end collar. 3. Bearings. 4. Outer end collar. 5. Shaft. 6. Duo-Cone seals. 7. Track roller.The flange at the center of shaft (5) gets the side load on the roller. Bearings (3) also get the side load on the roller. The amount of side movement or end clearance of the shaft can not be adjusted.The track rollers have Duo-Cone floating seals (6) at both ends of shaft (5).Track Roller Lubrication
TRACK ROLLER
1. Shaft. 2. Duo-Cone seals. 3. Plug. 4. Reservoirs. 5. Center passage.If lubricant is added with the roller removed from the machine, shaft (1) must be in a horizontal position. The slot, in the end where the 5M2080 Nozzle is installed, must be down.Lubricant is sent into center passage (5) through the 5M2080 Nozzle. The lubricant fills the reservoirs (4) in the rollers. When the reservoirs are full, the pressure of the oil causes the air and extra lubricant to go out the relief threads in the nozzle.When the lubricant does not have any bubbles, remove the nozzle and install the plug. Tighten the plug to a torque of 125 15 lb.ft. (17.3 2.1 mkg).Front Idlers
The front idlers put the tracks in position in front of the track rollers. They also keep the tracks in alignment with the sprockets.The adjustment of the tracks is done by the movement of the front idlers. The track adjusters move the front idlers and hold them in position.
FRONT IDLER
1. Bearing. 2. Bushing assemblies (two). 3. Duo-Cone seals (two). 4. Bearing. 5. Shaft. 6. End collars (two).The position of the front idlers is controlled
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
4176922
SEAL AS
797B, 797F
797B, 797F
3818975
SEAL-O-RING
795F AC, 795F XQ, 797B, 797F
795F AC, 795F XQ, 797B, 797F
3432873
SEAL-BELLOWS
735, 735B, 740, 740B
735, 735B, 740, 740B
3162314
SEAL
735, 740
735, 740
3017711
SEAL-FACE TYPE
730, 730C, 740, 740B
730, 730C, 740, 740B
2927835
SEAL
730, 730C, 740, 740B
730, 730C, 740, 740B
528, 528B, 530B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
4257486
SEAL-HEAD
797B, 797F
797B, 797F
2172732
SEAL-O-RING
797B
797B
3743464
SEAL-U-CUP
795F AC, 795F XQ, 797B, 797F
795F AC, 795F XQ, 797B, 797F
793F AC, 795F AC, 795F XQ, 797B, 797F