3500960 SEAL-U-CUP Caterpillar parts
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
Rating:
Alternative (cross code) number:
CA3500960
350-0960
3500960
CA3500960
350-0960
3500960
Weight: 0.06 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$7.85
18 Aug 2022
0.1102[0.05] Pounds
US: TakePart
CTP Caterpillar Seal-u-Cup (3500960)
CTP
CTP
$11.05
12 Jul 2022
0.1102[0.05] pounds
US: ProperBuy
CTP Caterpillar Seal-u-Cup (3500960)
CTP
CTP
$20.86
17 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL-U-CUP 3500960 NEW
Number on catalog scheme:
9
For full view, you need register
Compatible equipment models: 3500960:
Information:
Removal Procedure
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: The two cylinder, the three cylinder and the four cylinder engines have different configurations for the flywheel housing and the back plate. The removal process is similar for all models.
Illustration 1 g01305376
Typical example
Remove bolts (3) and remove the flywheel housing or back plate (2) from the cylinder block. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information.
Remove crankshaft rear seal (1) from the cylinder block. Discard the crankshaft oil seal. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01305365
Typical example
Ensure that the mating surface of cylinder block (5) and the flywheel housing or back plate (2) are clean and free from damage. Inspect dowels (4). If the dowels are damaged, use new parts for replacement.
Ensure that crankshaft flange (6) is clean and free from damage. It is possible to reclaim a crankshaft flange that has a worn seal surface, or a damaged seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Rear) - Remove and Install" for more information.
Apply clean engine lubricating oil to the flange of crankshaft (6) around the running surface of crankshaft rear seal.
Align a new crankshaft rear seal (1) with the flange of crankshaft (6). Carefully install crankshaft rear seal (1) onto the crankshaft flange.
Apply a continuous bead of Tooling (A) to the rear face of the cylinder block around the edge of crankshaft rear seal (1). Apply a continuous bead of Tooling (A) around plug (X).
Align the flywheel housing or back plate (2) to dowels (4). Install the flywheel housing or back plate (2) and install bolts (3) to cylinder block (5). Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information.
Tighten bolts (3). For C0.5 and C0.7 engines, tighten the bolts to a torque of 15 N m (11 lb ft).For C1.1 and C1.6 engines, tighten the bolts to a torque of 50 N m (37 lb ft).For C1.5 and C2.2 engines, tighten the bolts to a torque of 25 N m (19 lb ft).End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: The two cylinder, the three cylinder and the four cylinder engines have different configurations for the flywheel housing and the back plate. The removal process is similar for all models.
Illustration 1 g01305376
Typical example
Remove bolts (3) and remove the flywheel housing or back plate (2) from the cylinder block. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information.
Remove crankshaft rear seal (1) from the cylinder block. Discard the crankshaft oil seal. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01305365
Typical example
Ensure that the mating surface of cylinder block (5) and the flywheel housing or back plate (2) are clean and free from damage. Inspect dowels (4). If the dowels are damaged, use new parts for replacement.
Ensure that crankshaft flange (6) is clean and free from damage. It is possible to reclaim a crankshaft flange that has a worn seal surface, or a damaged seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Rear) - Remove and Install" for more information.
Apply clean engine lubricating oil to the flange of crankshaft (6) around the running surface of crankshaft rear seal.
Align a new crankshaft rear seal (1) with the flange of crankshaft (6). Carefully install crankshaft rear seal (1) onto the crankshaft flange.
Apply a continuous bead of Tooling (A) to the rear face of the cylinder block around the edge of crankshaft rear seal (1). Apply a continuous bead of Tooling (A) around plug (X).
Align the flywheel housing or back plate (2) to dowels (4). Install the flywheel housing or back plate (2) and install bolts (3) to cylinder block (5). Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for more information.
Tighten bolts (3). For C0.5 and C0.7 engines, tighten the bolts to a torque of 15 N m (11 lb ft).For C1.1 and C1.6 engines, tighten the bolts to a torque of 50 N m (37 lb ft).For C1.5 and C2.2 engines, tighten the bolts to a torque of 25 N m (19 lb ft).End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E...
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
3500953
SEAL-BUFFER
320D, 320E, 320E L, 320E RR, 321D LCR, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
320D, 320E, 320E L, 320E RR, 321D LCR, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
3500958
SEAL-U-CUP
320D, 320E, 320E L, 320E RR, 321D LCR, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
320D, 320E, 320E L, 320E RR, 321D LCR, 324D, 324D L, 324E, 324E L, 324E LN, 326D L
2668026
SEAL-O-RING
320D, 320D L, 323D L, 324D, 324D L, 325D L, 329D, 329D L
320D, 320D L, 323D L, 324D, 324D L, 325D L, 329D, 329D L
2590652
SEAL-BUFFER
320D, 320D L, 323D L, 323D LN, 323D SA, 324D, 324D L, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 323D L, 323D LN, 323D SA, 324D, 324D L, 325D, 325D L, 328D LCR, 329D, 329D L
2590653
SEAL-U-CUP
320D, 320D L, 323D L, 323D LN, 323D SA, 324D, 324D L, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 323D L, 323D LN, 323D SA, 324D, 324D L, 325D, 325D L, 328D LCR, 329D, 329D L
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
3776019
SEAL-U-CUP
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
3776020
SEAL-BUFFER
324D, 324D L, 324D LN, D10T2
324D, 324D L, 324D LN, D10T2
3776017
SEAL-U-CUP
324D, 324D L, 324D LN, D10T2
324D, 324D L, 324D LN, D10T2
2344498
SEAL-LIP TYPE
323D L, 323D LN, 325D, 325D L, M325D L MH, M325D MH
323D L, 323D LN, 325D, 325D L, M325D L MH, M325D MH
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2