3500961 SEAL-U-CUP Caterpillar parts
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
Rating:
Alternative (cross code) number:
CA3500961
350-0961
3500961
CA3500961
350-0961
3500961
Weight: 0.04 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 3500961:
Information:
Note: Use this procedure only if the engine does not shut down completely.Probable Causes
Diagnostic codes
Event codes
Air inlet and exhaust restrictions
Throttle signal
Power supply for the Electronic Control Module (ECM)
Fuel supplyRecommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.Diagnostic Codes and Event Codes
Certain diagnostic codes and/or event codes may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Air Inlet and Exhaust Restrictions
Ensure that the turbocharger is operating correctly. Periodic inspection and cleaning is recommended for the turbocharger compressor housing (inlet side).Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed. Refer to Troubleshooting, "Speed Control - Test".ECM Power Supply
Inspect the circuit between the ECM and the batteries. Refer to the Electrical System Schematic. Inspect the wires, the connectors, and the components in the circuit. Refer to Troubleshooting, "Electrical Power Supply - Test" for more information.
Inspect the circuit between the ECM and the keyswitch. Refer to the Electrical System Schematic. Inspect the wires, the connectors, and the components in the circuit. Refer to Troubleshooting, "Electrical Power Supply - Test" for more information. Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to the Operation and Maintenance Manual for more information.
Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting.
Check the fuel tank for foreign objects which may block the fuel supply.
Check the fuel filters.
Check the fuel quality. Make sure that the fuel meets the requirements of Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations ".
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Diagnostic codes
Event codes
Air inlet and exhaust restrictions
Throttle signal
Power supply for the Electronic Control Module (ECM)
Fuel supplyRecommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.Diagnostic Codes and Event Codes
Certain diagnostic codes and/or event codes may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Air Inlet and Exhaust Restrictions
Ensure that the turbocharger is operating correctly. Periodic inspection and cleaning is recommended for the turbocharger compressor housing (inlet side).Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed. Refer to Troubleshooting, "Speed Control - Test".ECM Power Supply
Inspect the circuit between the ECM and the batteries. Refer to the Electrical System Schematic. Inspect the wires, the connectors, and the components in the circuit. Refer to Troubleshooting, "Electrical Power Supply - Test" for more information.
Inspect the circuit between the ECM and the keyswitch. Refer to the Electrical System Schematic. Inspect the wires, the connectors, and the components in the circuit. Refer to Troubleshooting, "Electrical Power Supply - Test" for more information. Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to purge the air from the fuel system. Refer to the Operation and Maintenance Manual for more information.
Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting.
Check the fuel tank for foreign objects which may block the fuel supply.
Check the fuel filters.
Check the fuel quality. Make sure that the fuel meets the requirements of Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations ".
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
3500960
SEAL-U-CUP
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 3...
1336813
SEAL-LIP TYPE
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2
3776022
SEAL-BUFFER
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
3500956
SEAL-BUFFER
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
1915645
SEAL-BUFFER
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
2941849
SEAL-O-RING
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
1915646
SEAL-U-CUP
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 385C L
1540767
SEAL
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
1540770
SEAL
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
2552272
SEAL GP-DUO-CONE
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
328D LCR, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345C MH, 345D L, 349D L, 349E, 349E ...
1948364
SEAL-U-CUP
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
0931347
SEAL-O-RING
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
2590655
SEAL-LIP TYPE
320D, 320D L, 323D L, 323D LN, 323D SA, 325D, 325D L, 328D LCR, 329D, 329D L
320D, 320D L, 323D L, 323D LN, 323D SA, 325D, 325D L, 328D LCR, 329D, 329D L
2459362
SEAL
320D FM RR, 320D LRR, 320D RR
320D FM RR, 320D LRR, 320D RR
2459353
SEAL
320D FM RR, 320D LRR, 320D RR
320D FM RR, 320D LRR, 320D RR
3776022
SEAL-BUFFER
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
3776019
SEAL-U-CUP
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
1390, 2590, 320D, 320D FM, 320D2, 320D2 L, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E, 521B, 522B, 541, 541 2, 551, 552, 552 2
3776020
SEAL-BUFFER
324D, 324D L, 324D LN, D10T2
324D, 324D L, 324D LN, D10T2
3338673
SEAL-U-CUP
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C L MH
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C L MH
2095877
SEAL-LIP TYPE
330C L, 330D, 330D L, 336D, 336D L, 336D2, 345C, 345C L, 345C MH, W345C MH
330C L, 330D, 330D L, 336D, 336D L, 336D2, 345C, 345C L, 345C MH, W345C MH
2095876
SEAL-U-CUP
330C L, 330D, 330D L, 336D, 336D L, 345C, 345C L, 345C MH, W345C MH
330C L, 330D, 330D L, 336D, 336D L, 345C, 345C L, 345C MH, W345C MH
1915645
SEAL-BUFFER
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
324D, 325C, 325D L, 328D LCR, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 340D L, 345C, 345C L, 345C MH, 385C L, W345C MH
2003501
SEAL-O-RING
345B II, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, W345C MH
345B II, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, W345C MH
3500956
SEAL-BUFFER
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN
320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329E, 329E L, 329E LN