3843546 SEAL-AIR Caterpillar parts
Rating:
Alternative (cross code) number:
CA3843546
384-3546
3843546
CA3843546
384-3546
3843546
Weight: 0.01 pounds 0 kg.
Information:
Introduction
This instruction gives the procedure for using the 4C4069 [38.1 mm (1.5 in)] and 4C4070 [44.5 mm (1.75 in)] Seal Installers.The installer tool is used to install seals quickly and safely without damage.
InstallerInstallation Guidelines
Listed below are guidelines to follow that will help prevent seal damage during installation while using the installer. Proper usage of the installer will ensure optimum seal performance and service life.1. Clean and lubricate all gland hardware, shamban seal components and the installer tool. Check all hardware for burrs or sharp edges before installation.2. Install the elastomer ring (1) into gland assembly (2) as shown below.3. Using your fingers, collapse shamban seal (3) and install into gland assembly (2), as shown below. Use extreme care not to crease seal while installing into gland assembly. If necessary, heat seal in oil or water to 100°C (212°F) to assist in installation.4. Place installation tool (4) into gland assembly (2) as shown below. Installation tool is used to smooth out the I.D. of the seal after installation.5. Insert resizing tool (5), while twisting and pushing, into bore to size the seal. Remove the resizing tool from the seal and bore after one minute. The resizing tool must be fabricated to the specifications as shown below. The suggested material used for fabricating the tool is plastic.
(A) Bore diameter + 0.127 mm (+ .005 in). (B) Bore length + 50.8 mm (+ 2.00 in). When finishing resizing tool, round all edges. This will protect the seal from damage.6. For completion of seal installation, install rod into cylinder bore while twisting and pushing.
This instruction gives the procedure for using the 4C4069 [38.1 mm (1.5 in)] and 4C4070 [44.5 mm (1.75 in)] Seal Installers.The installer tool is used to install seals quickly and safely without damage.
InstallerInstallation Guidelines
Listed below are guidelines to follow that will help prevent seal damage during installation while using the installer. Proper usage of the installer will ensure optimum seal performance and service life.1. Clean and lubricate all gland hardware, shamban seal components and the installer tool. Check all hardware for burrs or sharp edges before installation.2. Install the elastomer ring (1) into gland assembly (2) as shown below.3. Using your fingers, collapse shamban seal (3) and install into gland assembly (2), as shown below. Use extreme care not to crease seal while installing into gland assembly. If necessary, heat seal in oil or water to 100°C (212°F) to assist in installation.4. Place installation tool (4) into gland assembly (2) as shown below. Installation tool is used to smooth out the I.D. of the seal after installation.5. Insert resizing tool (5), while twisting and pushing, into bore to size the seal. Remove the resizing tool from the seal and bore after one minute. The resizing tool must be fabricated to the specifications as shown below. The suggested material used for fabricating the tool is plastic.
(A) Bore diameter + 0.127 mm (+ .005 in). (B) Bore length + 50.8 mm (+ 2.00 in). When finishing resizing tool, round all edges. This will protect the seal from damage.6. For completion of seal installation, install rod into cylinder bore while twisting and pushing.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
9X7544
SEAL-O-RING
Caterpillar
Caterpillar
9S9643
SEAL-LIP TYPE
Caterpillar
Caterpillar
6V5809
SEAL-LIP TYPE
Caterpillar
Caterpillar
5594334
SEAL
Caterpillar
Caterpillar
5580994
SEAL
Caterpillar
Caterpillar
5580993
SEAL
Caterpillar
Caterpillar
4468489
SEAL-AIR
Caterpillar
Caterpillar
4468488
SEAL-AIR
Caterpillar
Caterpillar
4468485
SEAL-AIR
Caterpillar
Caterpillar
4335227
SEAL
Caterpillar
Caterpillar
4187962
SEAL-AIR
Caterpillar
Caterpillar
3843547
SEAL-AIR
Caterpillar
Caterpillar