3979067 SEAL-O-RING Caterpillar parts
320D, 320D2, 424B, 424B HD
Rating:
Alternative (cross code) number:
CA3979067
397-9067
3979067
CA3979067
397-9067
3979067
Weight: 0.02 pounds 0 kg.
BACKHOE LOADER, EXCAVATOR,
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 1 g02331933
Loosen clamp assemblies (1) , (3) and (5) .Note: Mark the orientation of clamp assembly (3) prior to removal.
Slide elbow (2) into bellows (4) in order to gain clearance. Remove the bellows assembly.Installation Procedure
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 2 g02095400
Illustration 3 g02332313
Alignment wrap (A) is not shown for photographic purposes. Typical ExampleNote: Alignment wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.Note: The alignment wrap (A) should not be removed until Step 11. Bellows (4) should never be flexed during installation.
Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (2) . a Distance (X) from the end of elbow (2) .
Insert elbow (2) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.
Illustration 4 g02331933
Alignment wrap (A) is not shown for photographic purposes.
Illustration 5 g02097701
The photo is a cutaway view of the ball clamp assembly which is located near the combustion head group.
Illustration 6 g02098533
The photo is a cutaway view of the ball clamp assembly.
Prior to installation, position both ball clamp assemblies (1) and (5) onto the bellows assembly.
Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (2) in the slip joint at clamp assembly (3) in order to position the bellows assembly.
Verify that the cup of the ball joint (E) does not touch the radius of the ball (D) . Position ball clamp (1) and hand tighten ball clamp (1) . Measure Distance (Y) and Distance (Z) . The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1) . If necessary, adjust ball clamp (1) .
Repeat Step 6 for ball clamp (5) which is located near the turbocharger.
Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (3) .Note: Do not use power tools in order to torque clamp assemblies (1) , (3) , and (5) .
Torque ball clamp (1) to a torque of 35 2 N m (26 1 lb ft).
Torque ball clamp (5) to a torque of 35 2 N m (26 1 lb ft).
Remove alignment wrap (A) from bellows (4) .
Torque clamp assembly (3) to a torque of 55 8 N m (41 6 lb ft).
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 1 g02331933
Loosen clamp assemblies (1) , (3) and (5) .Note: Mark the orientation of clamp assembly (3) prior to removal.
Slide elbow (2) into bellows (4) in order to gain clearance. Remove the bellows assembly.Installation Procedure
If reusing the exhaust elbow, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".
Illustration 2 g02095400
Illustration 3 g02332313
Alignment wrap (A) is not shown for photographic purposes. Typical ExampleNote: Alignment wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.Note: The alignment wrap (A) should not be removed until Step 11. Bellows (4) should never be flexed during installation.
Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (2) . a Distance (X) from the end of elbow (2) .
Insert elbow (2) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.
Illustration 4 g02331933
Alignment wrap (A) is not shown for photographic purposes.
Illustration 5 g02097701
The photo is a cutaway view of the ball clamp assembly which is located near the combustion head group.
Illustration 6 g02098533
The photo is a cutaway view of the ball clamp assembly.
Prior to installation, position both ball clamp assemblies (1) and (5) onto the bellows assembly.
Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (2) in the slip joint at clamp assembly (3) in order to position the bellows assembly.
Verify that the cup of the ball joint (E) does not touch the radius of the ball (D) . Position ball clamp (1) and hand tighten ball clamp (1) . Measure Distance (Y) and Distance (Z) . The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1) . If necessary, adjust ball clamp (1) .
Repeat Step 6 for ball clamp (5) which is located near the turbocharger.
Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (3) .Note: Do not use power tools in order to torque clamp assemblies (1) , (3) , and (5) .
Torque ball clamp (1) to a torque of 35 2 N m (26 1 lb ft).
Torque ball clamp (5) to a torque of 35 2 N m (26 1 lb ft).
Remove alignment wrap (A) from bellows (4) .
Torque clamp assembly (3) to a torque of 55 8 N m (41 6 lb ft).
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322C, 322...
318C, 319C, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320...
301.6C, 302.5C, 303, 304, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D...
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 314D CR, 314D LCR, 315D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 3...
320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322C, 323D L, 323D LN...
4548625
SEAL-O-RING
424B, 424B HD
424B, 424B HD
4540382
SEAL
424B, 424B HD
424B, 424B HD
4537343
SEAL-WIPER
424B, 424B HD
424B, 424B HD
4537342
SEAL
424B, 424B HD
424B, 424B HD
4537341
SEAL
424B, 424B HD
424B, 424B HD
4530709
SEAL
424B, 424B HD
424B, 424B HD
4540360
SEAL-O-RING
424B, 424B HD
424B, 424B HD
4548635
SEAL-WIPER
424B, 424B HD
424B, 424B HD
4548628
SEAL-WIPER
424B, 424B HD
424B, 424B HD
4548627
SEAL
424B, 424B HD
424B, 424B HD
4548624
SEAL-O-RING
424B, 424B HD
424B, 424B HD
4548623
SEAL
424B, 424B HD
424B, 424B HD