3G9194 SEAL-LIP TYPE Caterpillar parts
183B, 572G, 611, 613C, 613C II, 613G, 615, 615C, 623B, 623E, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 825C, 844, 844H, 844K, 930, 930R, 936, 936F, 950, 950B, 950B/950E, 950F, 950...
Rating:
Alternative (cross code) number:
CA3G9194
3G-9194
3G9194
CA3G9194
3G-9194
3G9194
Weight: 0.04 pounds 0 kg.
Information:
AXIAL WIDTH
6.35
mm
BORE DIAMETER
0
mm
CONSTRUCTION TYPE
DBM-HLR
MATERIAL
FKM Rubber - 80 Duro
SEAL OD
47.78
mm
SHAFT OD
36.5
mm
ARTICULATED TRUCK, WHEEL TRACTOR-SCRAPER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 3G9194:
Information:
Scheduling a Minor Overhaul
Generally, a minor overhaul is performed for every 3 to 4 thousand hours. The requirement for a minor overhaul is determined by several factors. The following are three specific factors that can be used to determine when a minor overhaul should be scheduled:
An increase in power end vibration
Excessive fluctuation in power end lube pressure
The presence of metallic or bearing debris in the lube tank or power end sump, or SOS sampleAn increase of wear metals in the lube oil is an indication of bearing surfaces beginning to degrade. This degradation results in the reduction of the ability for the bearings to create a sufficient oil film to protect the critical components of the power end. An increase in the level of noise or vibration can be an indicator of rotating parts in need of inspection or service.Note: Oil analysis may indicate a decrease of wear metals in the lube oil. The crosshead liners may be worn so that polishing of the bore occurs.Monitor the power end as the power end accumulates service hours. Consult your Cat dealer about scheduling a minor overhaul.Note: Refer to the literature that is provided by the OEM of the driving equipment.Minor Overhaul Information
For the minor overhaul, all the bearings, seals, gaskets, and components that wear are cleaned and inspected. If necessary, the parts are replaced.Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.The following definitions explain the terminology for the services that are performed during a minor overhaul:Inspect - Inspect the components according to the instructions that are in Caterpillar reusability publications.Refer to the following Guidelines for Reusable Parts, Salvage Operations, and Special Instructions:
M0067968 , "Reusability Inspection of Well Stimulation Pump Drivetrain Components"
, M0069554 , "Reusability Inspection of Well Stimulation Pump Crankshaft"The guidelines were developed to help Cat dealers and customers to avoid unnecessary expenditures. New parts are not required if the existing parts can still be used, reconditioned, or repaired. If the components are not in the reusability guidelines, refer to the SpecificationsService Manual.Rebuild - The component can be reconditioned to comply with reusability guidelines.Replace - The service life of the part is exhausted. The part may fail before the next maintenance interval. The part must be replaced with a part that meets functional specifications. Consult your Cat dealer about repair options.If you elect to perform an overhaul without the services of a Cat dealer, be aware of the recommendations in Table 1. Your Cat dealer can provide these services and components
Table 1
Minor Overhaul
Clean Internal Components
Internal Frame Sump
Lube Lines
Inspect Connecting Rods
Crankshaft
Crosshead
Crosshead Liners
Frame
Hardware
Pony Rods
Power End Drive Components
Roller Bearings
Seal Housings
Stay Rods
Replace Breather
Connecting Rod Nyloc Nuts
Crankshaft Seal
Gaskets
Pinion Seal
Pony Rod Seals
Rod Journal Bearings
Thrust Bearings
Generally, a minor overhaul is performed for every 3 to 4 thousand hours. The requirement for a minor overhaul is determined by several factors. The following are three specific factors that can be used to determine when a minor overhaul should be scheduled:
An increase in power end vibration
Excessive fluctuation in power end lube pressure
The presence of metallic or bearing debris in the lube tank or power end sump, or SOS sampleAn increase of wear metals in the lube oil is an indication of bearing surfaces beginning to degrade. This degradation results in the reduction of the ability for the bearings to create a sufficient oil film to protect the critical components of the power end. An increase in the level of noise or vibration can be an indicator of rotating parts in need of inspection or service.Note: Oil analysis may indicate a decrease of wear metals in the lube oil. The crosshead liners may be worn so that polishing of the bore occurs.Monitor the power end as the power end accumulates service hours. Consult your Cat dealer about scheduling a minor overhaul.Note: Refer to the literature that is provided by the OEM of the driving equipment.Minor Overhaul Information
For the minor overhaul, all the bearings, seals, gaskets, and components that wear are cleaned and inspected. If necessary, the parts are replaced.Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.The following definitions explain the terminology for the services that are performed during a minor overhaul:Inspect - Inspect the components according to the instructions that are in Caterpillar reusability publications.Refer to the following Guidelines for Reusable Parts, Salvage Operations, and Special Instructions:
M0067968 , "Reusability Inspection of Well Stimulation Pump Drivetrain Components"
, M0069554 , "Reusability Inspection of Well Stimulation Pump Crankshaft"The guidelines were developed to help Cat dealers and customers to avoid unnecessary expenditures. New parts are not required if the existing parts can still be used, reconditioned, or repaired. If the components are not in the reusability guidelines, refer to the SpecificationsService Manual.Rebuild - The component can be reconditioned to comply with reusability guidelines.Replace - The service life of the part is exhausted. The part may fail before the next maintenance interval. The part must be replaced with a part that meets functional specifications. Consult your Cat dealer about repair options.If you elect to perform an overhaul without the services of a Cat dealer, be aware of the recommendations in Table 1. Your Cat dealer can provide these services and components
Table 1
Minor Overhaul
Clean Internal Components
Internal Frame Sump
Lube Lines
Inspect Connecting Rods
Crankshaft
Crosshead
Crosshead Liners
Frame
Hardware
Pony Rods
Power End Drive Components
Roller Bearings
Seal Housings
Stay Rods
Replace Breather
Connecting Rod Nyloc Nuts
Crankshaft Seal
Gaskets
Pinion Seal
Pony Rod Seals
Rod Journal Bearings
Thrust Bearings
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
2U9113
SEAL
D250D, D250E, D25D, D300E, D350E, D400E, D40D
D250D, D250E, D25D, D300E, D350E, D400E, D40D
1049658
SEAL-ROD
D25D, D300D, D300E, D350E, D400E, D40D
D25D, D300D, D300E, D350E, D400E, D40D
2U5343
SEAL-O-RING
D250B, D25C, D25D, D300B, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D
D250B, D25C, D25D, D300B, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D
5U3529
SEAL-WIPER
D250B, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
D250B, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
2U5379
SEAL
D250B, D25C, D25D, D300B, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
D250B, D25C, D25D, D300B, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B
2U5377
SEAL
D250B, D250D, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D35C, D35HP, D400, D40D, D44B, D550B
D250B, D250D, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D35C, D35HP, D400, D40D, D44B, D550B
6P8369
SEAL
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
9G7127
SEAL
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
8T0208
SEAL-PIVOT SHAFT
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
9W5210
SEAL-LIP TYPE
D10N, D8L, D9N
D10N, D8L, D9N
5P5520
SEAL-LIP TYPE (168.43MM OD)
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
8C3077
SEAL
D10N, D10R, D8L, D9L, D9N, D9R
D10N, D10R, D8L, D9L, D9N, D9R
5G2063
SEAL
931B
931B
5P7485
SEAL .28m(11.02 in.)
814B, 815B, 816B, 824C, 826C, 916, 926, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980F, D4E, G936
814B, 815B, 816B, 824C, 826C, 916, 926, 950B, 950B/950E, 950F, 966D, 966F, 980C, 980F, D4E, G936
6V1949
SEAL
183B, 826H, 834G, 834H, 836G, 836H, 844, 844H, 854G, 854K, 926, 930R, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980C, 988B, 988F, 988F II, 988G, 988H, 990, 99...
183B, 826H, 834G, 834H, 836G, 836H, 844, 844H, 854G, 854K, 926, 930R, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980C, 988B, 988F, 988F II, 988G, 988H, 990, 99...
9P6083
SEAL (filters panel)
920, 955L
920, 955L
2V9002
SEAL (U-cup)
955K, 955L, 963
955K, 955L, 963
0041525
SEAL
183B
183B
5P5663
SEAL .106 m(4.19 in.)
931B, 931C II, 966D, 980C, 980F, D6C
931B, 931C II, 966D, 980C, 980F, D6C
4B7952
SEAL
572G
572G
1D8947
SEAL
D4D, D7F
D4D, D7F