3S4489 SEAL-O-RING Caterpillar parts
1673C, 3304, 3306, 3406, 3408, 3408B, 3412, 3412D, 3412E, 69D, 769C, 769D, 771C, 771D, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777, 777D, 784B, 784C, 785B, 785C, 789B, 789C, 793B, 793C, 793D, ...
Rating:
Alternative (cross code) number:
CA3S4489
3S-4489
3S4489
CA3S4489
3S-4489
3S4489
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
2.62
mm
DASH SIZE
141
ID
58.42
mm
MATERIAL
Silicone (VMQ) Rubber - 70 Duro
OD
0
mm
INDUSTRIAL ENGINE, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 3S4489:
Information:
System Operation Description:If the voltage rises above the generator over voltage percentage threshold set point value, then the over voltage timer will begin timing. When the timer expires, the generator over voltage event is made active if the voltage has been above the threshold level continuously while timing. If the voltage drops below the generator over voltage percentage threshold, then the generator over voltage event will be made inactive. The timer will be reset.If an over voltage condition is detected, then "GEN OVERVOLTAGE SHUTDOWN" or "GEN OVERVOLTAGE " will be displayed on the EMCP 3. The message is used to inform the operator of an over voltage condition.Note: The severity of the over voltage condition will determine if a warning or shutdown event occurs.The code for generator over voltage is generated when the EMCP 3 determines that a generator over voltage condition has occurred.Test Step 1. TALK TO THE OPERATOR.
Determine the conditions that caused the over voltage condition.Expected Result:An over voltage was caused by an occurrence known to the operator and the operator would like to put the generator set back into service.Results:
OK - The operator can determine the cause for the over voltage condition. The condition has been repaired, and the operator wants to put the generator set back into service.Repair: Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The over voltage condition was not caused by an occurrence that is known to the operator. Proceed to Test Step 2.Test Step 2. CHECK THE SET POINTS.
View the generator over voltage set points. Make a note of the set points. Refer to Testing and Adjusting, RENR7902, "Electronic Control Module (Generator Set) - Configure". Compare the set points against the default set points of the particular generator set.Expected Result:The set points are correct.Results:
OK - The set points are correct for your particular generator set.Repair: Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The set points are NOT correct.Repair: Reprogram the set points. Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOPTest Step 3. VERIFY VOLTAGE CAN BE ADJUSTED.Verify that the generator output voltage can be adjusted from the EMCP 3 display.Expected Result:The generator output voltage can be adjusted from the EMCP 3 display.Results:
OK - The generator output voltage can be changed from the EMCP 3 display.Repair: Adjust the generator output voltage to meet site requirements. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The generator output voltage cannot be adjusted. Proceed to test step 4.Test Step 4. CHECK CAT DATA LINK BETWEEN THE EMCP 3 AND THE VOLTAGE REGULATOR.Refer to the generator set electrical system schematic in the service manual. Check the data link wiring between the EMCP 3 and the voltage regulator. For more information on troubleshooting the data link, refer to Troubleshooting , RENR7902, "Data Link Circuit Fault ".Results:
OK - The data link wiring is correct.Repair: Refer
Determine the conditions that caused the over voltage condition.Expected Result:An over voltage was caused by an occurrence known to the operator and the operator would like to put the generator set back into service.Results:
OK - The operator can determine the cause for the over voltage condition. The condition has been repaired, and the operator wants to put the generator set back into service.Repair: Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The over voltage condition was not caused by an occurrence that is known to the operator. Proceed to Test Step 2.Test Step 2. CHECK THE SET POINTS.
View the generator over voltage set points. Make a note of the set points. Refer to Testing and Adjusting, RENR7902, "Electronic Control Module (Generator Set) - Configure". Compare the set points against the default set points of the particular generator set.Expected Result:The set points are correct.Results:
OK - The set points are correct for your particular generator set.Repair: Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The set points are NOT correct.Repair: Reprogram the set points. Reset the generator set. Resume normal operation and verify that the problem has been corrected.STOPTest Step 3. VERIFY VOLTAGE CAN BE ADJUSTED.Verify that the generator output voltage can be adjusted from the EMCP 3 display.Expected Result:The generator output voltage can be adjusted from the EMCP 3 display.Results:
OK - The generator output voltage can be changed from the EMCP 3 display.Repair: Adjust the generator output voltage to meet site requirements. Resume normal operation and verify that the problem has been corrected.STOP
NOT OK - The generator output voltage cannot be adjusted. Proceed to test step 4.Test Step 4. CHECK CAT DATA LINK BETWEEN THE EMCP 3 AND THE VOLTAGE REGULATOR.Refer to the generator set electrical system schematic in the service manual. Check the data link wiring between the EMCP 3 and the voltage regulator. For more information on troubleshooting the data link, refer to Troubleshooting , RENR7902, "Data Link Circuit Fault ".Results:
OK - The data link wiring is correct.Repair: Refer
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
1627864
SEAL GP-DUO-CONE
D10N, D10R, D10T, D10T2, D11R, D11T
D10N, D10R, D10T, D10T2, D11R, D11T
9X7487
SEAL AS-SHAFT
D10R, D10T, D10T2, D9R, D9T
D10R, D10T, D10T2, D9R, D9T
8T0208
SEAL-PIVOT SHAFT
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
8P9142
SEAL
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
2077107
SEAL AS
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
2239058
SEAL AS
D10R, D10T, D10T2
D10R, D10T, D10T2
5P5520
SEAL-LIP TYPE (168.43MM OD)
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
8E8994
SEAL-RING
D10R, D10T, D10T2, D9R, D9T
D10R, D10T, D10T2, D9R, D9T
1375532
SEAL-LIP TYPE
D10R, D10T
D10R, D10T
1686448
SEAL-LIP TYPE
D9R, D9T
D9R, D9T
2074849
SEAL-O-RING
D10T
D10T
2D1521
SEAL
12E, D8H, D8K
12E, D8H, D8K
3E6773
SEAL-O-RING
3408B, 3412, 3412C, 3412D, 3412E, 374F L, 390F L, 572R II, 583T, 587R, 587T, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 797F, 980H, 980K, 980K HLG, 980M, 982M, C30, C32, D10T, D10T2, D11R, D11T...
3408B, 3412, 3412C, 3412D, 3412E, 374F L, 390F L, 572R II, 583T, 587R, 587T, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 797F, 980H, 980K, 980K HLG, 980M, 982M, C30, C32, D10T, D10T2, D11R, D11T...
1974727
SEAL AS
3408B, 3412, 3412E, C30, C32
3408B, 3412, 3412E, C30, C32
1003091
SEAL
3408B, 3412, 3412E, C30, C32
3408B, 3412, 3412E, C30, C32
1003080
SEAL
3408B, 3412, 3412E
3408B, 3412, 3412E
6F8146
SEAL-O-RING
12E, 12F, 140, 140B, 14E, 1676, 235C, 235D, 3406, 3408, 3408B, 3408C, 3412, 3516B, 55, 589, 621, 637, 637B, 637D, 637E, 639D, 69D, 768C, 769C, 769D, 770, 771C, 771D, 772, 772B, 773B, 773D, 773E, 773F,...
12E, 12F, 140, 140B, 14E, 1676, 235C, 235D, 3406, 3408, 3408B, 3408C, 3412, 3516B, 55, 589, 621, 637, 637B, 637D, 637E, 639D, 69D, 768C, 769C, 769D, 770, 771C, 771D, 772, 772B, 773B, 773D, 773E, 773F,...
6V3830
SEAL-O-RING
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D...
16G, 16H NA, 24H, 24M, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D...
8M4390
SEAL-O-RING
14E, 1693, 24H, 24M, 3508B, 3512B, 3516, 3516B, 3516C, 572G, 572R, 572R II, 578, 583K, 583R, 583T, 587R, 587T, 589, 594H, 621, 621B, 621E, 621F, 621G, 623, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 62...
14E, 1693, 24H, 24M, 3508B, 3512B, 3516, 3516B, 3516C, 572G, 572R, 572R II, 578, 583K, 583R, 583T, 587R, 587T, 589, 594H, 621, 621B, 621E, 621F, 621G, 623, 623B, 623E, 623F, 623G, 627B, 627E, 627F, 62...
1121102
SEAL-O-RING
3406B, 3406C, 3406E, 3412, 3412E, 3612, 3616, 785D, C-15, C-16, C15, C18, C30, C32, D10N, D10R, D11T, D6T LGP, D6T LGPPAT, D6T XL, G3406
3406B, 3406C, 3406E, 3412, 3412E, 3612, 3616, 785D, C-15, C-16, C15, C18, C30, C32, D10N, D10R, D11T, D6T LGP, D6T LGPPAT, D6T XL, G3406
1313719
SEAL-O-RING
16G, 16H NA, 3406B, 3406C, 3408B, 3408C, 3412, 3412C, 3412E, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D250E II, D...
16G, 16H NA, 3406B, 3406C, 3408B, 3408C, 3412, 3412C, 3412E, 375, 375 L, 5080, 578, 583R, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980F II, 980G, D250E II, D...
8M4431
SEAL
3412, 578, 621, 623, 627, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633D, 633E II, 637, 637B, 637D, 637E, 637G, 639D, 641B, 650B, 657B, 666, 931B, D250D, D250E, D250E II, D25C, D25D, D300D, D300E, D30...
3412, 578, 621, 623, 627, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633D, 633E II, 637, 637B, 637D, 637E, 637G, 639D, 641B, 650B, 657B, 666, 931B, D250D, D250E, D250E II, D25C, D25D, D300D, D300E, D30...
1135304
SEAL-O-RING
14M, 16G, 16H NA, 16M, 24M, 3406B, 3406C, 3406E, 3412, 3412C, 3412E, 3456, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3616, 365C, 365C L...
14M, 16G, 16H NA, 16M, 24M, 3406B, 3406C, 3406E, 3412, 3412C, 3412E, 3456, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3616, 365C, 365C L...
7E4847
SEAL-O-RING
16G, 3406B, 3406C, 3408B, 3412, 375, 375 L, 578, 621E, 621F, 623E, 627E, 627F, 826C, 980C, 980F, D8N, RR-250, SS-250
16G, 3406B, 3406C, 3408B, 3412, 375, 375 L, 578, 621E, 621F, 623E, 627E, 627F, 826C, 980C, 980F, D8N, RR-250, SS-250