AVSPARE.COM
parts catalog

SEAL-BUFFER 4415676 - Caterpillar



4415676 SEAL-BUFFER Caterpillar parts SEAL
Rating:
31
Alternative (cross code) number:
CA4415676
441-5676
4415676
Caterpillar 4415676 SEAL-BUFFER
Weight: 7 pounds 3 kg.

Buy SEAL-BUFFER 4415676 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 11
 
  For full view, you need register

Information:

3000 Frame End Bracket Installation
Start By:
Ensure that the main rotor assembly has been properly installed. Refer to the Disassembly and Assembly, "Rotor - Remove and Installation" section of this document.
Ensure that the high density protective plastic strips have been installed between the stator and the rotor. The protective plastic strips protect the rotor and the stator and assist in centering the rotor.
Ensure that the exciter rotor and the exciter stator have been properly installed. Refer to the Disassembly and Assembly, "Exciter - Remove and Install" section of this document.
Ensure that the rear bearing has been properly installed. Refer to the Disassembly and Assembly, "Rear Bearing - Remove and Install" section of this document.
Ensure that the rotating leads are protected in order to prevent damage to the leads as the end bracket is installed. Note: The end bracket can be removed and installed independent of the rotor removal.
Table 1
Required Tools
Qty Part Number Description
2 FT3220(1) Polyethylene Strips - Thickness of 5 mm or Wedge
4 FT3219(1) Guide Stud
(1) Drawings for fabricated tools can be found at https://dealer.cat.com/dealer-service-tools
Use a suitable lifting device (6) in order to position end bracket (13) onto the main rotor shaft (1). The weight of end bracket and the main rotor is approximately 3000 kg (6600 lb). Note: Ensure that the alignment mark (10) that was made on the end bracket will match the alignment mark that was made on the stator housing.
Illustration 1 g01657413
Position the end bracket onto the main rotor shaft as close as possible to the stator housing. Align the end bracket mounting holes to the main stator housing. Install four guide pins (12) through the end bracket (13) into the main stator housing.
Illustration 2 g01651114
Install the end bracket mounting bolts. Do not tighten the installed bolts. Remove the guide pins (12). Install the remaining end bracket mounting bolts. Torque the end bracket mounting bolts.
Move the bearing retainer into the correct position. Install the bearing retainer mounting bolts (15).
Illustration 3 g01660076
Remove the cribbing (17).
Illustration 4 g01660093
Install the PMG components. Refer to the Disassembly and Assembly, "PMG Installation Procedure" section of this publication.
Install the rotating diode components and the varistor. Refer to the Disassembly and Assembly, "Diode Assembly - Remove and Install" section of this publication.

Caterpillar parts catalog:

Caterpillar parts catalog
994K Wheel Loader SMX00001-UP (MACHINE) POWERED BY 3516 Engine
994K Wheel Loader MM900001-UP (MACHINE) POWERED BY 3516B Engine
994K Wheel Loader MRK00001-UP (MACHINE) POWERED BY 3516B Engine


Parts seal Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.