AVSPARE.COM
parts catalog

SEAL 44162 - Caterpillar



44162 SEAL Caterpillar parts WE-851B SEAL
Rating:
64
Alternative (cross code) number:
CA44162
4-4162
44162
Caterpillar 44162 SEAL

Buy SEAL 44162 Caterpillar genuine, new aftermarket tractor parts with delivery
WINDROW ELEVATOR,

You can buy parts: .

$46.65

05 May 2021

US: Locate Ball Bearings
Timken 44162 Tapered Roller Bearing, Single Cone, Standard Tolerance, Straight Bore, Steel, Inch, 1.6250" ID, 0.9330" Width
TIMKEN Single cone (inner ring) for connecting to compatible cups (outer rings, sold separately) to form a complete single tapered roller bearing || Supports both radial and axial loads between a rotating and non-rotating member || Operating temperatures range from -54 to 120 degrees C (-65 to 250 degrees F) || Stamped steel cage evenly spaces rollers for reduced friction, vibration, and noise || Open configuration for lubrication applied in place
$15.50

14 Apr 2021
5.0[2.25] Pounds
-: -
Scag Linkage, Dump Valve Part # 44162
Genuine OEM Part
Number on catalog scheme: 61
 
  For full view, you need register

Compatible equipment models: 44162:

WINDROW ELEVATOR  WE-851B   Caterpillar

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1114 Vacuum Cap 1
B 504-9791 Lift Gp (60 Hz)(1) 1
OR
504-9793 Lift Gp (50 Hz)(2) 1
C 8S-7615 Pin 2
283-1495 Stand Assembly 2
8S-7611 Tube 2
(1) High-Voltage (480V) Low-Voltage (240V)
(2) High-Voltage (400V) Low-Voltage (200V)Start By:
Remove the wheels and the tires from both sides of the machine.Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned to prevent dirt from entering the internal mechanism.
Illustration 1 g00910597
Install Tooling (A) on the hydraulic tank. Attach hose (1A) to the nipple on Tooling (A) and to an air supply. Apply 276 414 kPa (40 60 psi) of air. This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g01024977
Disconnect hose assemblies (1). Remove all the hardware from the hose assemblies to axle assembly (2).
Illustration 3 g01021671
Disconnect hose assemblies (3) and (4).
Illustration 4 g06289372
Attach a suitable lifting device to axle assembly (2).
Use Tooling (B) to raise axle assembly (2) off Tooling (C). Remove Tooling (C). Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (B).
Illustration 5 g01021673
Remove bolt (5). Remove pin assembly (6).
Illustration 6 g01021674
Remove axle assembly (2) and remove spacers (7). The weight of axle assembly (2) is approximately 1134 kg (2500 lb).
Illustration 7 g01021675
Remove seals (8) and bearings (9).

Caterpillar parts catalog:

Caterpillar parts catalog
WE-851B WINDROW ELEVATOR 8BC00205-UP (MACHINE)


Parts seal Caterpillar catalog:

6V8399 SEAL-O-RING
10 FT, 10-20B, 16H, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 235C, 235D, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 245B, 246C, 246D, 247, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 25...
4130 SEAL
PR-105, WE-851B
4130 SEAL
PR-105, WE-851B
E810369 SEAL
PS-110, PS-130, PS-180
E810246 SEAL, QUAD RING
PS-110, PS-130, PS-180
5900145 SEAL
PS-110, PS-130, PS-180
E810245 SEAL
PS-110, PS-130, PS-180
E810063 SEAL, OIL
PS-110, PS-130, PS-180
56000137 SEAL
CB-414, CB-514
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.