4L4360 SEAL --TO OUTPUT FLANGE Caterpillar parts
3192, 7241, 7251
Rating:
Alternative (cross code) number:
CA4L4360
4L-4360
4L4360
CA4L4360
4L-4360
4L4360
Weight: 1 pounds 0 kg.
Information:
AXIAL WIDTH
19.05
mm
BORE DIAMETER
0
mm
CONSTRUCTION TYPE
SBI
MATERIAL
Nitrile Rubber (NBR) - 75 Duro
SEAL OD
238.33
mm
SHAFT OD
200.02
mm
MARINE GEAR, MARINE TRANSMISSION,
For full view, you need register
Information:
indicates that the EFR has detected that the PWM command from the Drivetrain ECM is out of range. Proceed to Test Step 2.
NO - The frequency of the feedback signal is in the expected range, however the duty cycle of the feedback signal is not approximately 80 percent. The EFR has not detected that the duty cycle of the PWM command is out of range. Proceed to Test Step 5.Test Step 2. CHECK THE ECM POWER SUPPLY
Turn the key start switch and the battery disconnect switch to the OFF position.
At the Drivetrain ECM, use the spoon type multimeter probes to check the ECM 5 volt power supply. Insert the positive probe along the supply circuit wire at connector contact J1-11 (wire E864) and insert the negative probe along the ECM ground circuit wire at contact J2-8 (wire N877).
Turn the battery disconnect switch and the key start switch to the ON position. Do not start the Engine. Observe the voltage of the power supply.Expected Result:The voltage measurement of the ECM power supply is 5.0 0.3 VDC.Results:
OK - The voltage of the ECM power supply is in the range of 5.0 0.3 VDC. The ECM voltage supply is correct. Proceed to Test Step 3.
NOT OK - The voltage of the ECM power supply is not in the range of 5.0 0.3 VDC. There is a problem with the ECM 5.0 VDC power supply.Repair: Turn the key start switch OFF. At the EFR, disconnect the 14 contact control voltage connector. Turn the key start switch to the ON position. Check the voltage between power contact N and the ground contact D.If the voltage is in the correct range with the EFR disconnected, there is a problem in the EFR that is affecting the power supply. Replace the EFR.If the voltage is not in the correct range with the EFR disconnected, there is a problem at either in the machine harness or possibly with the ECM 5.0 power supply. Refer to the MID 081, CID 0262 troubleshooting procedures for the 5.0 VDC power supply in this section of the manual in order to determine the cause of the power supply problem.STOPTest Step 3. CHECK THE CURRENT COMMAND CIRCUIT FOR AN OPEN
Turn the key start switch and the battery disconnect switch to the OFF position.
At the EFR, disconnect the 14 contact control circuit harness connector from the module connector. Visually inspect each of the connector contacts for damage or contamination. Verify that the contacts are clean, secured in the connector, and in good condition.
At the control circuit harness connector for the EFR, connect a jumper wire between the
NO - The frequency of the feedback signal is in the expected range, however the duty cycle of the feedback signal is not approximately 80 percent. The EFR has not detected that the duty cycle of the PWM command is out of range. Proceed to Test Step 5.Test Step 2. CHECK THE ECM POWER SUPPLY
Turn the key start switch and the battery disconnect switch to the OFF position.
At the Drivetrain ECM, use the spoon type multimeter probes to check the ECM 5 volt power supply. Insert the positive probe along the supply circuit wire at connector contact J1-11 (wire E864) and insert the negative probe along the ECM ground circuit wire at contact J2-8 (wire N877).
Turn the battery disconnect switch and the key start switch to the ON position. Do not start the Engine. Observe the voltage of the power supply.Expected Result:The voltage measurement of the ECM power supply is 5.0 0.3 VDC.Results:
OK - The voltage of the ECM power supply is in the range of 5.0 0.3 VDC. The ECM voltage supply is correct. Proceed to Test Step 3.
NOT OK - The voltage of the ECM power supply is not in the range of 5.0 0.3 VDC. There is a problem with the ECM 5.0 VDC power supply.Repair: Turn the key start switch OFF. At the EFR, disconnect the 14 contact control voltage connector. Turn the key start switch to the ON position. Check the voltage between power contact N and the ground contact D.If the voltage is in the correct range with the EFR disconnected, there is a problem in the EFR that is affecting the power supply. Replace the EFR.If the voltage is not in the correct range with the EFR disconnected, there is a problem at either in the machine harness or possibly with the ECM 5.0 power supply. Refer to the MID 081, CID 0262 troubleshooting procedures for the 5.0 VDC power supply in this section of the manual in order to determine the cause of the power supply problem.STOPTest Step 3. CHECK THE CURRENT COMMAND CIRCUIT FOR AN OPEN
Turn the key start switch and the battery disconnect switch to the OFF position.
At the EFR, disconnect the 14 contact control circuit harness connector from the module connector. Visually inspect each of the connector contacts for damage or contamination. Verify that the contacts are clean, secured in the connector, and in good condition.
At the control circuit harness connector for the EFR, connect a jumper wire between the
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140...
120, 12E, 12F, 14E, 16G, 16H, 16H NA, 16M, 183, 184, 225, 235, 235C, 235D, 245, 245B, 245D, 304C CR, 305D CR, 305E, 318C, 3192, 319C, 320C, 320C FM, 320C L, 321C, 322C, 322C FM, 324D, 324D FM, 324D FM...
16, 183B, 24H, 24M, 30/30, 301.7D, 302.2D, 302.7D, 3192, 3406, 3406B, 3456, 35, 45, 5110B, 515, 517, 518, 518C, 525, 525B, 525C, 527, 528, 528B, 530B, 535B, 535C, 545, 545C, 55, 561C, 561D, 561M, 561N...
24H, 24M, 3192, 3406, 3406B, 3508, 3508C, 3512, 3516, 5130, 5130B, 5230B, 583H, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637, 637B, 637D, 637E, 637G, 639D, 65, 657G, 65C, 65E, 75, 75C, 75D, ...
10 FT, 10B, 118, 120B, 120G, 129, 12E, 12F, 12G, 130G, 140, 140G, 141, 14E, 153, 16, 160G, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 205B, 211B, 215, 215B, 215C, 215D, 225, 231D, 235D, 245, 3192,...
1674, 1676, 1693, 30/30, 3192, 3406, 3406B, 3408, 3408B, 3412, 3512, 3516, 508, 518, 518C, 528, 528B, 530B, 561C, 578, 611, 615, 615C, 621, 623, 627, 637D, 637E, 65, 657E, 65C, 65E, 69D, 7261, 7271, 7...
1140, 1145, 1150, 1160, 120G, 12G, 130G, 140, 140G, 153, 16, 160G, 163, 172, 183, 184, 191, 216, 225, 228, 236, 245, 247, 248, 267, 287, 3145, 3150, 3160, 3192, 3208, 416E, 44, 46, 518, 518C, 527, 528...
120G, 130G, 140G, 16G, 215, 235, 245, 3208, 3304, 3306, 3306B, 3406, 3406B, 3408, 3412, 3508, 3512, 3516, 518, 561C, 572G, 589, 613, 613B, 613C, 627E, 631E, 637E, 651E, 657E, 7241, 815B, 824G, 824G II...
120H, 120H ES, 120H NA, 120K, 120K 2, 12F, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 14G, 16, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16G, 18...
120G, 120H, 120H ES, 120H NA, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H NA, 140G, 140H NA, 140M, 140M 2, 140M 3, 140M 3 AWD, 14E, 14G, 14M, 160G, 160H NA, 160M, 160M 2, 160M 3, 160M ...
3192, 3406, 7231, 7261, 7271, D343, D353C
120B, 12E, 140, 140B, 191, 322B L, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 666, 7241, 943, 953, M325C MH
4L4355
SEAL --TO PILOT RING
3192, 7261
3192, 7261
24H, 24M, 3192, 550, 550B, 560B, 570, 570B, 580, 580B, 583H, 583K, 621, 621B, 621E, 621F, 621G, 621H, 621K, 623F, 623G, 623H, 623K, 623K LRC, 630B, 631B, 633, 7241, 7251, 824C, 824G, 824G II, 824H, 82...
3D1084
SEAL --TO OUTPUT BEARING SPACER
3192, 7241, 7251
3192, 7241, 7251
D346, D353C
950G, 950G II, 962G, 962G II, D346, D348, D353C, IT62G, IT62G II
D346, D348, D353C
1673, 1676, 1693, 621, 641B, 666, 992, D336, D343, D348, D379A, D399
12E, 1673, 1676, 1693, 3406, 528, 621, 621E, 627B, 627E, 631E, 637D, 637E, 641B, 650B, 651, 651E, 657E, 666, 769, 769C, 773B, 776, 777, 910, 931, 931B, 977H, 980, 992, D3, D326F, D334, D336, D342, D34...
120G, 12G, 130G, 140B, 14G, 1673C, 215, 225, 235, 3208, 3304, 3306, 518, 613B, 627B, 637D, 772, 941, 950, 955L, D4D, D4E, D5, D5B, D6C, D6D
120B, 12G, 130G, 140B, 14G, 16, 1673C, 1693, 225, 3304, 3306, 528, 561C, 621R, 627, 631C, 633D, 637D, 641, 651, 657, 657B, 666, 768B, 769, 824B, 825B, 826B, 834, 920, 930, 941, 950, 951B, 955K, 966C, ...
583T, 587R, 587T, 69D, 7261, 7271, AD40, AD45, AD55, AE40, AE40 II