AVSPARE.COM
parts catalog

SEAL AS-OIL 4P6531 - Caterpillar


4P6531 SEAL AS-OIL Caterpillar parts
Rating:
61
Alternative (cross code) number:
CA4P6531
4P-6531
4P6531
Caterpillar 4P6531 SEAL AS-OIL
Weight: 0.02 pounds 0 kg.

Buy SEAL AS-OIL 4P6531 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01329939
Front left engine view
(1) Fuel manifold (Rail)
(2) Canister for the crankcase breather
(3) Electronic control module
(4) P2 connector
(5) Secondary fuel filter
(6) Hand primer
(7) Primary fuel filter
(8) Oil sampling valve
(9) Oil filter
(10) Fuel pump
(11) Water pump
(12) Damper
(13) Fan
(14) Fan pulley
(15) Belt tensioner
Illustration 2 g01329941
Rear right engine view
(16) Oil gauge
(17) Air intake
(18) Oil filler
(19) Front lifting eye
(20) Alternator
(21) Exhaust manifold
(22) Exhaust elbow
(23) Turbocharger
(24) Wastegate solenoid
(25) Starting motor
(26) Oil pan
(27) Drain plug (oil)
(28) Drain plug or coolant sampling valve
(29) Breather
(30) Rear lifting eye The C6.6 diesel engine is electronically controlled. The C6.6 engine has an Electronic Control Module (ECM) that receives signals from the fuel injection pump and other sensors in order to control the electronic unit injector. The fuel injection pump supplies fuel to the high pressure manifold (Rail). The high pressure manifold (Rail) distributes fuel to the electronic unit injectors.The six cylinders are arranged in-line. The cylinder head assembly has two inlet valves and two exhaust valves for each cylinder. The ports for the exhaust valves are on the right side of the cylinder head. The ports for the inlet valves are on the left side of the cylinder head. Each cylinder valve has a single valve spring.Each cylinder has a piston cooling jet that is installed in the cylinder block. The piston cooling jet sprays engine oil onto the inner surface of the piston in order to cool the piston. The pistons have a Quiescent combustion chamber in the top of the piston in order to achieve clean exhaust emissions. The piston pin is off-center in order to reduce the noise level.The pistons have two compression rings and an oil control ring. The groove for the top ring has a hard metal insert in order to reduce wear of the groove. The skirt has a layer of graphite in order to reduce the risk of seizure when the engine is new. The correct piston height is important in order to ensure that the piston does not contact the cylinder head. The correct piston height also ensures the efficient combustion of fuel which is necessary in order to conform to requirements for emissions.A piston and a connecting rod are matched to each cylinder. The piston height is controlled by the distance between the center of the big end bearing and the center of the small end bearing of the connecting rod. Three different lengths of connecting rods are available in order to attain the correct piston height. The three different lengths of connecting rods are made by machining the blank small end bearing of each rod at three fixed distances vertically above the centerline of the big end bearing.The crankshaft has seven main bearing journals. End play is controlled by thrust washers which are located on both sides of the number six main bearing.The timing case is made of aluminum. The timing gears are stamped with timing marks in order to ensure the correct assembly of the gears. When the number 1 piston is at the top center position of


Parts seal Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.