SEAL-CRANKSHAFT 4W5359 - Caterpillar

Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 366-3469 Mounting Bar 2
B - Guide Stud
5/8 - 11 by 12 inch 8
8T-4122 Hard Washer 8
6V-4803 Thrust Bearing 8
4K-0367 Full Nut 16
C 4C-5591 Anti-Seize Compound -
F 366-3468 Cover Plate 6
G 2D-7325 Pipe Tee 3
8T-0853 Pressure Gauge 3
4C-7121 Nipple 3
129-3078 Shutoff Valve Assembly 3
4C-7158 Fitting 3
5P-3413 Pipe Sealant -
H 4C-7121 Nipple 3
129-3078 Shutoff Valve Assembly 3
4C-7000 Bushing 3
7W-8705 Fitting 3
5P-0720 Hose 1
5P-3413 Pipe Sealant - Note: The following story is for 300-5617 Sea Water Heat Exchanger Gp.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02130836
Install liners (8) and collars (7) in the ports of the rear frame.Note: The liners are installed through the rear of the rear frame.
Illustration 2 g06097989
Illustration 3 g02146927
Position gasket (9) on the heat exchanger plate (6). Install tabs (X) of the gasket into the slots of heat exchanger plate (6). Install ring seals (10) into the grooves of first heat exchanger plate.Note: Use tape to hold ring seal (10) in the grooves of the first heat exchanger plate.
Illustration 4 g06097990
Install gaskets (9) onto the rest of the heat exchanger plates (6).
Illustration 5 g02141318
Illustration 6 g02105674
(A) Rear frame
(B) Front of the engine
(J) 327-1133 Plate Assembly
(K) 327-1134 Plate Assembly
(L) 327-1136 Plate Assembly 449-3078 Seal
(M) 327-1135 Plate Assembly 149-2213 Seal
(N) 327-1136 Plate Assembly 149-2213 Seal
(P) 327-1137 Plate Assembly
(R) 327-1115 Plate Assembly
(S) 327-1135 Plate Assembly 149-2213 SealNote: Seal 149-2213 needs to be cut to match each plateNote: Ensure the proper order and orientation of the heat exchanger plates and the gaskets.Note: The gaskets on the heat exchanger plates should face the rear frame during installation.Note: Use Tooling (A) to ensure that the heat exchanger plates are properly aligned.Note: Ensure that the edges of the heat exchanger plates are properly aligned and the gaskets are in the proper grooves in the heat exchanger plates.Note: If the heat exchanger plates do not lay flat during installation on the rear frame, one side of Tooling (A) may be loosened and retightened to accommodate the heat exchanger plates.Note: If the heat exchanger plates appear stuck together or do not align during installation, the edges of the heat exchanger plates can be lightly lifted and adjusted.
Install heat exchanger plates (6) and the gaskets.
Install the liners and the collars in front frame (2). Install front frame (2).Note: The liners are installed from the front of the front frame.
Install Tooling (B) in the spacers. Ensure that Tooling (B) is securely installed. Apply Tooling (C) to the threads of the nut and the threads of the guide stud prior to installation.
Illustration 7 g02104418
Tighten the nuts on Tooling (B) evenly until the front frame contacts the spacers.Note: As the front frame lowers, the heat exchanger plates will slide along Tooling (A).Note: Check the heat exchanger plates, the gaskets, and the gasket tabs frequently during