SEAL-LIP TYPE 5433698 - Caterpillar

5433698 SEAL-LIP TYPE Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA5433698
543-3698
5433698

Weight: 0.07 pounds 0 kg.

Buy SEAL-LIP TYPE 5433698 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

72mm Outer Diameter Lip Compatible with CAT 320GX 320GC 323 323GC EXCAVATOR

$130.00

28 Oct 2025

CN: QX construction

72mm Outer Diameter Lip Compatible with CAT 320GX 320GC 323 323GC EXCAVATOR
DJCXYSM Product Name:72mm Outer Diameter Lip || Part Number:543-3698 5433698 || Application:Compatible with CAT 320GX 320GC 323 323GC EXCAVATOR || NOTE: To avoid unnecessary returns please check the part number before purchasing or tell us the picture of your engine model and nameplate to reduce the error rate. || TIP: If you cannot find the required product part number, please consult us and we will reply as soon as possible.

$128.00

28 Oct 2025

CN: Fikowjs-Machine

72mm Outer Diameter Lip Compatible with CAT 320GX 320GC 323 323GC EXCAVATOR
Fikowjs TIP: Please purchase according to the old part number, appearance is not able to judge the accuracy of the product. || Product Name:72mm Outer Diameter Lip || Part Number:543-3698 5433698 || Application:Compatible with CAT 320GX 320GC 323 323GC EXCAVATOR || NOTE: There are many kinds of products in Fikowjs parts, if you can't find the part number you need, please consult us, we will reply soon!

5433697 4649758 5433698 GASKET and oil Compatible With CAT320 GC (Black-Rubber-4649758 GASKET)

$95.00

05 Aug 2025

HK: SHANDIEN

5433697 4649758 5433698 GASKET and oil Compatible With CAT320 GC (Black-Rubber-4649758 GASKET)
Generic

Number on catalog scheme: 8

Caterpillar 5433698 Parts scheme SEAL-LIP TYPE

For full view, you need register

Information:

Illustration 1 g00721817
System Schematic For kW Level OutputThe kW level output will be activated whenever the total power output of the generator exceed the setpoint P139. The kW level output is the connector contact 34 of the GSC+. This setpoint can be programmed from 0 to 110 percent of the rated power on the nameplate (setpoint P030). This setpoint can be programmed with a time delay from 0 to 120 seconds (setpoint P140). See System Operation, "Engine/Generator Programming OP5-0". Also, see System Operation, "Service Mode". Once the output is activated, the kW level output will be deactivated when the total power output of the generator drops below a programmed setpoint (setpoint P141). This setpoint is different from the activation setpoint. This setpoint can be programmed from 0 to 110 percent of the power rating on the nameplate of the generator. This setpoint can be programmed with a time delay from 0 to 120 seconds.When kW relay is disconnected from the GSC+, the voltage on the kW level output is approximately 5.0 DCV. When kW relay is connected to the GSC+, the voltage on the kW level output is approximately 0 volts. The kW level output is capable of drawing (sinking) approximately 100 mA. Documenting and troubleshooting any connections to this output is the responsibility of the customers and the dealers. The possible cause of a CID 0859 FMI 03 is a short to the +battery circuit of the kW level output.The GSC+ treats a CID 0859 FMI 03 as an alarm fault.Troubleshooting of this failure is straight forward. The FMI 03 defines the problem as a short to "B+". Use the following information in order to find the exact cause of the diagnostic code.
FMI information
system schematic of the kW level output
customer's documentation
dealer's documentationTest Step 1. CHECK THE GENERATOR SET CONTROL
Verify that the CID 0859 FMI 03 diagnostic code is active.
Disconnect the wire from contact 34 of the GSC+.
Measure the voltage between contact 34 of the GSC+ and"B-".Expected Result:The voltage is approximately 5 1.0 DCV.Results:
OK - The voltage is approximately 5 1.0 DCV. The voltage is correct. Proceed to test step 2.
NOT OK - The voltage is NOT approximately 5 1.0 DCV. The voltage is NOT correct. The GSC+ has failed.Repair: It