5P2673 SEAL Caterpillar parts
245, 24H, 24M, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 844, 844H, 844K, 854G, 854K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, 990, 990 II, 990H, 990K, 992G, 992K, AD40, AD45, AD45B, AD55, AD...
Rating:
Alternative (cross code) number:
CA5P2673
5P-2673
5P2673
CA5P2673
5P-2673
5P2673
Weight: 0.20 pounds 0 kg.
Information:
AXIAL WIDTH
7.92
mm
BORE DIAMETER
152.32
mm
MATERIAL
Polyurethane - 90 Duro
SEAL OD
152.55
mm
SHAFT OD
133.35
mm
EXCAVATOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$22.07
18 Oct 2023
US: FinditParts Inc
5P2673 - SEAL-LIP TYPE fits Caterpillar (CAT)
BLUMAQ 5P2673 - SEAL-LIP TYPE fits Caterpillar (CAT)
BLUMAQ 5P2673 - SEAL-LIP TYPE fits Caterpillar (CAT)
$22.04
28 Feb 2022
US: Florida-Parts-Z
5P2673 - Seal-Lip Type for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 5P2673:
EXCAVATOR
245
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 1P-7409 Eyebolt 1
D 1P-1861 Retaining Ring Pliers 1
E 5P-5197 Retaining Ring Pliers As 1
G 1H-3110 Bearing Puller Gp 1
J 138-7573 Link Bracket 2
N 136-1452 Retaining Ring Pliers As 1
P 1U-8846 Gasket Sealant 1
Q 6V-6640 Sealant 1
R FT-0947 Clamps 1 Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Lubricate all seals before assembling.
Illustration 1 g01191697
Install seal (163).
Illustration 2 g01191694
Install bearings (161), disks (160), and gears (161). Install pins (159) and (158). Repeat for the remaining planetary gears.
Illustration 3 g01192075
Illustration 4 g01191692
Attach Tooling (J) and a suitable lifting device to planetary assembly (156). The weight of planetary assembly (156) is approximately 54 kg (120 lb). Secure planetary assembly (156) on Tooling (B). Install bearing (157).
Illustration 5 g01191618
If necessary, install dowel (155). Install seals (154).
Illustration 6 g01191616
Attach Tooling (J) and a suitable lifting device to ring gear (153). The weight of ring gear (153) is approximately 23 kg (50 lb). Install ring gear (153).
Illustration 7 g01191615
Install bearing (151) and seal (150) into retainer (152).
Illustration 8 g01192085
Install retainer assembly (149). Use Tooling (E) in order to install retaining ring (148). Note: Bearing (151) must be aligned to dowel (155).
Illustration 9 g01192122
Install ring gear (145), discs (146), and plates (147).
Illustration 10 g01192573
Raise the temperature of bearing (144) in order to install bearing (144).
Illustration 11 g01191402
Install seal (143).
Illustration 12 g01191401
Raise the temperature of seal carrier (140) in order to install seal carrier (140). Install a new dowel (141). Install seals (142).
Illustration 13 g01191400
Install rotating housing (138). Use Tooling (E) to install retaining ring (139).
Illustration 14 g01191399
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install seal (137) onto clutch piston (136).
Install clutch piston (136) and springs (135). Install seal (134) onto balance piston (133). Install balance piston (133) and bolts (132).
Illustration 15 g01191398
Attach Tooling (C) and a suitable lifting device to shaft assembly (131). The weight of shaft assembly (131) is approximately 64 kg (140 lb).
Position shaft assembly (131). Install bolts (129) and (130).
Illustration 16 g01191397
Lower the temperature of manifold (127) and position the manifold onto center manifold (128). Install bolts (126).
Illustration 17 g01191396
Attach Tooling (J) and a suitable lifting device to center manifold assembly (124). The weight of center manifold assembly (124)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 1P-7409 Eyebolt 1
D 1P-1861 Retaining Ring Pliers 1
E 5P-5197 Retaining Ring Pliers As 1
G 1H-3110 Bearing Puller Gp 1
J 138-7573 Link Bracket 2
N 136-1452 Retaining Ring Pliers As 1
P 1U-8846 Gasket Sealant 1
Q 6V-6640 Sealant 1
R FT-0947 Clamps 1 Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Lubricate all seals before assembling.
Illustration 1 g01191697
Install seal (163).
Illustration 2 g01191694
Install bearings (161), disks (160), and gears (161). Install pins (159) and (158). Repeat for the remaining planetary gears.
Illustration 3 g01192075
Illustration 4 g01191692
Attach Tooling (J) and a suitable lifting device to planetary assembly (156). The weight of planetary assembly (156) is approximately 54 kg (120 lb). Secure planetary assembly (156) on Tooling (B). Install bearing (157).
Illustration 5 g01191618
If necessary, install dowel (155). Install seals (154).
Illustration 6 g01191616
Attach Tooling (J) and a suitable lifting device to ring gear (153). The weight of ring gear (153) is approximately 23 kg (50 lb). Install ring gear (153).
Illustration 7 g01191615
Install bearing (151) and seal (150) into retainer (152).
Illustration 8 g01192085
Install retainer assembly (149). Use Tooling (E) in order to install retaining ring (148). Note: Bearing (151) must be aligned to dowel (155).
Illustration 9 g01192122
Install ring gear (145), discs (146), and plates (147).
Illustration 10 g01192573
Raise the temperature of bearing (144) in order to install bearing (144).
Illustration 11 g01191402
Install seal (143).
Illustration 12 g01191401
Raise the temperature of seal carrier (140) in order to install seal carrier (140). Install a new dowel (141). Install seals (142).
Illustration 13 g01191400
Install rotating housing (138). Use Tooling (E) to install retaining ring (139).
Illustration 14 g01191399
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install seal (137) onto clutch piston (136).
Install clutch piston (136) and springs (135). Install seal (134) onto balance piston (133). Install balance piston (133) and bolts (132).
Illustration 15 g01191398
Attach Tooling (C) and a suitable lifting device to shaft assembly (131). The weight of shaft assembly (131) is approximately 64 kg (140 lb).
Position shaft assembly (131). Install bolts (129) and (130).
Illustration 16 g01191397
Lower the temperature of manifold (127) and position the manifold onto center manifold (128). Install bolts (126).
Illustration 17 g01191396
Attach Tooling (J) and a suitable lifting device to center manifold assembly (124). The weight of center manifold assembly (124)
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
1659290
SEAL-LIP TYPE
320B, 320C, 322B L, 322B LN, 322C, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L...
320B, 320C, 322B L, 322B LN, 322C, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L...
1672217
SEAL AS-BUFFER
1390, 2590, 320C, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329E, 330B L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 345B, 345B II, 345B ...
1390, 2590, 320C, 322C, 324D, 324D L, 324E, 324E L, 324E LN, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329E, 330B L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 345B, 345B II, 345B ...
1709864
SEAL-U-CUP
320C, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329E, 330B L, 330C, 330C FM...
320C, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 328D LCR, 329D, 329D L, 329E, 330B L, 330C, 330C FM...
8C9179
SEAL AS
345C, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, AD45B, CR20, P16
345C, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, AD45B, CR20, P16
1672219
SEAL AS-BUFFER
834G, 834H, TK1051
834G, 834H, TK1051
5P5520
SEAL-LIP TYPE (168.43MM OD)
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
4J9964
SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
8J2330
SEAL
120G, 120H, 120H ES, 120H NA, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 24H
120G, 120H, 120H ES, 120H NA, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 24H
1731007
SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1010509
SEAL-INTEGRAL
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
1659954
SEAL-LIP TYPE
24H, 24M
24H, 24M
5P7176
SEAL .7 m(27.56 in.)
215, 235, 245
215, 235, 245
6J1500
SEAL
215
215
3G2911
SEAL ASSEM.
225, 225D, 229, 229D, 231D
225, 225D, 229, 229D, 231D
9J9848
SEAL
235, 245
235, 245
8J5476
SEAL
14G, 16G, 235D, 245, 245B, 245D
14G, 16G, 235D, 245, 245B, 245D
4K7472
SEAL
235D, 245, 245B, 245D, 955H
235D, 245, 245B, 245D, 955H
9D8042
SEAL
245, 5130, 5130B, 561D, 725, 725C, 730, 730C, 735, 943, 953, 953B, 963, 963B, AP-1200, AP-800, CP-563, D5B, D5E, PM-201, PM-465, PM-565, PM-565B
245, 5130, 5130B, 561D, 725, 725C, 730, 730C, 735, 943, 953, 953B, 963, 963B, AP-1200, AP-800, CP-563, D5B, D5E, PM-201, PM-465, PM-565, PM-565B
0553676
SEAL
245
245
5J1808
SEAL
120G, 215, 215B, 834B, 950B, 950B/950E, 963, 966D, 973, 977K, 980C, 988
120G, 215, 215B, 834B, 950B, 950B/950E, 963, 966D, 973, 977K, 980C, 988
5P8190
SEAL
245, 245B, 508
245, 245B, 508
3S2824
SEAL
215, 627, 627B, 637, 941, 951B
215, 627, 627B, 637, 941, 951B
7K9212
SEAL
215C, 215D, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 24H, 24M, 320D, 324D L, 325B L, 325C, 325D L, 329D L, 834B, 834G, 836, 836G, 924G, 924GZ, 924H, 924HZ, 926, 926A, 928F, 928HZ, 930G, 938K...
215C, 215D, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 235D, 24H, 24M, 320D, 324D L, 325B L, 325C, 325D L, 329D L, 834B, 834G, 836, 836G, 924G, 924GZ, 924H, 924HZ, 926, 926A, 928F, 928HZ, 930G, 938K...