5P9375 SEAL Caterpillar parts
345B L, 785, 789, 950G, 962G, 966H, 972H, 993K
Rating:
Alternative (cross code) number:
CA5P9375
5P-9375
5P9375
CA5P9375
5P-9375
5P9375
Weight: 0.01 pounds 0 kg.
EXCAVATOR, WHEEL LOADER,
Compatible equipment models: 5P9375:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove".
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00516618
Typical example
Install Tooling (A) on flywheel housing (1). Use a suitable lifting device. The weight of the flywheel housing is approximately 111 kg (245 lb).
Remove bolts (2). Remove flywheel housing (1) from the dowels in the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00516618
Typical exampleNote: During assembly, inspect the following components for any foreign materials: the front face of the flywheel housing, both sides of the flywheel housing gasket, and the rear face of the cylinder block. These components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds, and any other foreign material.
Install Tooling (A) on the flywheel housing (1). Use a suitable lifting device. The weight of the flywheel housing is approximately 111 kg (245 lb).
Position flywheel housing (1) on the dowels in the cylinder block. Install bolts (2) and remove Tooling (A) .
Illustration 3 g00551652
Bolt tightening sequence
Tighten the bolts, as follows:
In a numerical sequence, tighten bolt 1 through bolt 9.Torque for bolts ... 100 20 N m (74 15 lb ft)
In a numerical sequence, tighten bolt 10 through bolt 24.Torque for bolts ... 40 10 N m (30 7 lb ft)
In a numerical sequence, again tighten bolt 1 through bolt 9.Torque for bolts ... 135 20 N m (100 15 lb ft)
In a numerical sequence, again tighten bolt 10 through bolt 24.Torque for bolts ... 55 10 N m (41 7 lb ft)End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove".
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00516618
Typical example
Install Tooling (A) on flywheel housing (1). Use a suitable lifting device. The weight of the flywheel housing is approximately 111 kg (245 lb).
Remove bolts (2). Remove flywheel housing (1) from the dowels in the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00516618
Typical exampleNote: During assembly, inspect the following components for any foreign materials: the front face of the flywheel housing, both sides of the flywheel housing gasket, and the rear face of the cylinder block. These components must be free of the following substances: oil, fuel, water, gasket adhesive, assembly compounds, and any other foreign material.
Install Tooling (A) on the flywheel housing (1). Use a suitable lifting device. The weight of the flywheel housing is approximately 111 kg (245 lb).
Position flywheel housing (1) on the dowels in the cylinder block. Install bolts (2) and remove Tooling (A) .
Illustration 3 g00551652
Bolt tightening sequence
Tighten the bolts, as follows:
In a numerical sequence, tighten bolt 1 through bolt 9.Torque for bolts ... 100 20 N m (74 15 lb ft)
In a numerical sequence, tighten bolt 10 through bolt 24.Torque for bolts ... 40 10 N m (30 7 lb ft)
In a numerical sequence, again tighten bolt 1 through bolt 9.Torque for bolts ... 135 20 N m (100 15 lb ft)
In a numerical sequence, again tighten bolt 10 through bolt 24.Torque for bolts ... 55 10 N m (41 7 lb ft)End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
328D LCR, 329D L, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D L, 336D L, 345B II, 345B II MH, 345B L, 345D L, 350, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 5080,...
330C, 330D L, 330D MH, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L, 515, 525, 525B, 525C, 535...
322B L, 325B L, 330 FM L, 330B L, 330C, 330D L, 330D MH, 345B, 345B II, 345B L, 345C, 345C L, 345D L, 350, E450
322B L, 322C FM, 325B L, 330B L, 345B II, 345B L, 345C, 350, 350 L, CR20, M325B, P16, W330B
322B L, 322C FM, 325B L, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C L, 345B II, 345B L, 345C, 350, 350 L, CR20, M325B, M325C MH, M325D L MH, P16, W330B
320 L, 320B, 320N, 322B, 322B LN, 325, 325 L, 325 LN, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330C L, 345B II, 345B L, M325B
320 L, 320B, 320B L, 320N, 321B, 345B, 345B L, OEMS
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
330, 330 L, 345B, 345B II, 345B L, 350, OEMS
330C, 330D L, 330D MH, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
992G, R1700 II, R1700G, R2900, R2900G
992G, R1700 II, R1700G, R2900, R2900G
5130B, 5230, 5230B, 992G, 992K, D11R, D11T
5130B, 5230, 992G
992G, 992K, D11R, D11T
3554073
SEAL-RECTANGULAR
834G, 834H, 836G, 836H, 988G, 988H, 993K, D8T, D9T
834G, 834H, 836G, 836H, 988G, 988H, 993K, D8T, D9T
797, 834G, 834H, 836G, 836H, 844K, 854K, 988G, 988H, 990K, 992K, 993K, D10T, D10T2, D8T, D9T
797, 797B, 797F, 834G, 834H, 836G, 836H, 854G, 988G, 988H
797, 797B, 797F, 834G, 834H, 836G, 836H, 854G, 988G, 988H, S25
1630818
SEAL
966G, 972G
966G, 972G
966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE