6K5974 SEAL Caterpillar parts
245, 518, 518C, 528, 528B, 530B, 561C, 571G, 930, D4
Rating:
Alternative (cross code) number:
CA6K5974
6K-5974
6K5974
CA6K5974
6K-5974
6K5974
Weight: 0.01 pounds 0 kg.
Information:
AXIAL WIDTH
3.53
mm
ID
21.82
mm
MATERIAL
RUBBER
OD
28.88
mm
RADIAL HEIGHT
3.53
mm
BACKHOE, WHEEL SKIDDER,
Compatible equipment models: 6K5974:
Number on catalog scheme:
6
For full view, you need register
Information:
Measure the Isolators
Spring Type Isolators
Illustration 1 g00545733
7C-0533 Generator Base Mounting Group
(1) Snubber bolt
Illustration 2 g00545734
7C-6537 Generator Base Mounting Group
(1) Snubber bolt Obtain dimension (B) for each isolator. If any of the following conditions are found, adjust the isolators:
Dimension (B) is different from the original dimension that was obtained during the engine commissioning.
Dimension (B) is not within 3 mm (.12 inch) for all of the isolators.
Snubber bolts (1) are not finger tight against the plates.For instructions on adjustment, see Special Instruction, SEHS9162, "Spring Isolator Group Installation and Adjustment Procedure".Resilient Isolators
Illustration 3 g00270544
(A) Dimension between the top of the soleplate and the bottom of the engine support assembly.
Measure the loaded height of each isolator. Use an inside micrometer and measure dimension (A) between the top of the soleplate and the bottom of the engine support assembly. Measure each corner of each isolator in order to ensure that the top and the bottom of each isolator is parallel. The four measurements for each isolator should not differ by more than 0.5 mm (.02 inch).Compare the measurements to the specifications from the engine commissioning. Adjust the height of the engine support assembly in order to maintain the specifications for alignment.Adjust the Height Of the Engine Support Assembly, If Necessary
Note: When shims are used in order to maintain the height of the engine support assembly, the alignment of the engine and the driven equipment must be verified.
Illustration 4 g00270557
(1) Setscrew. (2) Shim.
To adjust the height of the engine support assembly, use setscrew (1). To raise the height of the engine support assembly, add shims (2). To reduce the height of the engine support assembly, remove shims (2).Maintain a record of all of the shims that are added from the time of the engine commissioning. When the combined total of the shims that are added to any isolator exceeds 5 mm (.2 inch), the isolator must be repaired or replaced.
Spring Type Isolators
Illustration 1 g00545733
7C-0533 Generator Base Mounting Group
(1) Snubber bolt
Illustration 2 g00545734
7C-6537 Generator Base Mounting Group
(1) Snubber bolt Obtain dimension (B) for each isolator. If any of the following conditions are found, adjust the isolators:
Dimension (B) is different from the original dimension that was obtained during the engine commissioning.
Dimension (B) is not within 3 mm (.12 inch) for all of the isolators.
Snubber bolts (1) are not finger tight against the plates.For instructions on adjustment, see Special Instruction, SEHS9162, "Spring Isolator Group Installation and Adjustment Procedure".Resilient Isolators
Illustration 3 g00270544
(A) Dimension between the top of the soleplate and the bottom of the engine support assembly.
Measure the loaded height of each isolator. Use an inside micrometer and measure dimension (A) between the top of the soleplate and the bottom of the engine support assembly. Measure each corner of each isolator in order to ensure that the top and the bottom of each isolator is parallel. The four measurements for each isolator should not differ by more than 0.5 mm (.02 inch).Compare the measurements to the specifications from the engine commissioning. Adjust the height of the engine support assembly in order to maintain the specifications for alignment.Adjust the Height Of the Engine Support Assembly, If Necessary
Note: When shims are used in order to maintain the height of the engine support assembly, the alignment of the engine and the driven equipment must be verified.
Illustration 4 g00270557
(1) Setscrew. (2) Shim.
To adjust the height of the engine support assembly, use setscrew (1). To raise the height of the engine support assembly, add shims (2). To reduce the height of the engine support assembly, remove shims (2).Maintain a record of all of the shims that are added from the time of the engine commissioning. When the combined total of the shims that are added to any isolator exceeds 5 mm (.2 inch), the isolator must be repaired or replaced.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
518, 613, 613B, 950
508, 518, 910, 916, 920, 926, 980, 980B, CS-643, D35C, D44B, D550B, G926, IT18B, IT28, IT28B
518, 910, 916, 920, CS-643, IT18B
518, 528, 528B, 530B, 910, 920, 930, 950
518, 518C, 631D, SH-56B
120G, 12G, 130G, 140G, 140H NA, 143H, 160G, 160H NA, 163H NA, 518C, 528, 528B, 530B, 936, 936F, 950B/950E
518, 525D, 528, 535D, 545D, 555D, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M...
528, 528B, 530B, 533, 543, 816B, 950F, 950F II, 960F, 966C, 966F, 966F II, 970F, HA770, HA771, HA870, HA871, R1600, R1600G, R1600H, TK370, TK371, TK380, TK381
508, 528, 528B, 530B, 950B, 950B/950E, 966C, D25D, D300E, D350E
528, 528B, 530B, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G
515, 518C, 525
518, 518C, 528, 528B, 530B
245
245, 990, 990 II
245, 561H, 561M, 561N, PL61
245, 988, 992C, 992D, 992G, 994, 994D, 994F
2V0297
SEAL
235
235
5P5900
SEAL (use as required)
215, 613, 613B, 613C, 615C, 769C, 773B, 776, 777, 955K, 955L
215, 613, 613B, 613C, 615C, 769C, 773B, 776, 777, 955K, 955L
215, 229, 229D, 515, 5230, 525, 824G II, 824H, 834G, 834H, 943, 963, 973, AD30, D6T, D7E, R1300, R1300G, R1300G II
215, 215B, 615, 615C, 621, 621B, 621E, 627B, 627E, 630B, 631B, 631D, 631E, 633, 633D, 637D, 637E, 641B, 651, 666, 789, 8S, 936, 963, 977K, 977L, 980C, 988, 9A, D7H, D8N, G936
215, 215B, 215C, 215D