SEAL-O-RING 6K6307 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, in order to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance.Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Aftercooler Core - Clean/Test
Battery - Recycle
Battery - Replace
Battery or Battery Cable - Disconnect
Belt Tightener - Lubricate
Coolant - Change
Coolant Extender (ELC) - Add
Engine Oil Level Gauge - Calibrate
Engine Storage Procedure - Check
Fuel System - Prime
Generator - Dry
Generator Set - Test
Generator Set Alignment - Check
Generator Winding - Test
Heat Exchanger - Clean/Test
Heat Exchanger - Inspect
Maintenance Recommendations
Sea Water Strainer - Clean/Inspect
Daily
Coolant Level - Check
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Generator Load - Check
Power Factor - Check
Walk-Around Inspection
Every Week
Generator Bearing Temperature - Test/Record
Standby Generator Set Maintenance Recommendations
Stator Winding Temperature - Test
Voltage and Frequency - Check
Initial 20 to 40 Service Hours
Belts - Inspect/Adjust/Replace
Every 50 Service Hours or Weekly
Aftercooler Condensate Drain Valve - Inspect/Clean
Engine Cooling System Corrosion Protection System - Inspect
Sea Water Strainer - Clean/Inspect
Every 250 Service Hours
Coolant Sample (Level 1) - Obtain
Fan Drive Bearing - Lubricate
First 14 400 L (3750 US gal) of Fuel or 250 Service Hours
Engine Crankcase Breather - Clean
Engine Valve Rotators - Inspect
Engine Valve Lash - Check
Fuel Injector - Check
Every Year
Coolant Sample (Level 2) - Obtain
Varistor - Check
Varistor - Inspect
Every 14 400 L (3750 US gal) of Fuel or 250 Service Hours or 1 Year
Battery Charger - Check
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine - Clean
Engine Oil Sample - Obtain
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Coolant Sample (Level 2) - Obtain
Every 28 500 L (7500 US gal) of Fuel or 500 Service Hours or 1 Year
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Initial 1000 Service Hours
Heat Exchanger - Inspect
Every 1000 Service Hours
Engine Air Cleaner Element (Single Element) - Inspect/Replace
Every 2 Years
Belt Tightener - Lubricate
Every 57 000 L (15 000 US gal) of Fuel or 1000 Service Hours
Turbocharger - Inspect
Every 2000 Service Hours
Fumes Disposal Filter Element - Replace
Generator - Inspect
Generator Bearing - Lubricate
Generator Set Vibration - Inspect
Generator Winding Insulation - Test
Stator Lead - Check
Radiator - Clean
Every 170 400 L (45 000 US gal) of Fuel or 3000 Service Hours
Auxiliary Water Pump (Bronze Impeller) - Inspect/Replace
Belts - Inspect/Adjust/Replace
Coolant Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine Crankcase Breather - Clean
Engine Mounts - Inspect
Engine Valve Lash -