6V3671 SEAL Caterpillar parts
621E, 623E, 627E, 631E, 633E II, 637E, 651E, 657E, 916, 936, D10N, D11N, D6H, D6H XL, D6H XR, D6R, D6R II, D6R STD, D7H, D7R II, D7R XR, D8L, D8N, D9L, D9N, IT28
Rating:
Alternative (cross code) number:
CA6V3671
6V-3671
6V3671
CA6V3671
6V-3671
6V3671
Weight: 0.03 pounds 0 kg.
INTEGRATED TOOLCARRIER, WHEEL TRACTOR,
Compatible equipment models: 6V3671:
Number on catalog scheme:
23
For full view, you need register
Information:
Conditions Which Generate This Code:
Illustration 1 g01941579
Connections of the primary shifterThis diagnostic code is associated with the primary shifter. This diagnostic code is recorded when the ECU reads a problem that is internal to the shifter.The Cat data link is an input and an output of all electronic control modules. The data link is designed to carry communications between all electronic control modules. The data link is not a visible component. The data link consists of internal control circuits and the connecting wire harness.The possible causes of this diagnostic code are listed below:
The shifter is not recognized by the ECU.
The shifter has failed.
The part number for the software of the ECU is incorrect.
The ECU has failed.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2990 FMI 12 is active before performing this procedure.Test Step 1. VERIFY THE SOFTWARE VERSION.Note: Check and record the latest software version for the machine electronic controls from SIS.
Verify that the latest version of software has been loaded to the ECU.Expected Result:All of the software is current.Results:
OK - All of the software is current. Proceed to Test Step 2.
NOT OK - There is a more recent software release that is available.Repair: Flash all controls with the latest software release. Refer to Testing and Adjusting, KENR8292, "Electronic Control Unit - Flash Program".STOPTest Step 2. VERIFY THAT THE SHIFTER IS PRESENT.
Verify that the ECU recognizes the shifter.Expected Result:The ECU recognizes the installation of the shifter.Results:
OK - The ECU recognizes the installation of the shifter.Repair: The shifter may have failed. Replace the shifter. Proceed to Test Step 3.
NOT OK - The ECU does not recognize the installation of the shifter. Remove the shifter and then install the shifter. Proceed to Test Step 3.Test Step 3. VERIFY THAT THE DIAGNOSTIC CODE IS PRESENT.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all of the harness connectors. Make sure that the connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 2990 FMI 12 is active.Expected Result:
Illustration 1 g01941579
Connections of the primary shifterThis diagnostic code is associated with the primary shifter. This diagnostic code is recorded when the ECU reads a problem that is internal to the shifter.The Cat data link is an input and an output of all electronic control modules. The data link is designed to carry communications between all electronic control modules. The data link is not a visible component. The data link consists of internal control circuits and the connecting wire harness.The possible causes of this diagnostic code are listed below:
The shifter is not recognized by the ECU.
The shifter has failed.
The part number for the software of the ECU is incorrect.
The ECU has failed.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2990 FMI 12 is active before performing this procedure.Test Step 1. VERIFY THE SOFTWARE VERSION.Note: Check and record the latest software version for the machine electronic controls from SIS.
Verify that the latest version of software has been loaded to the ECU.Expected Result:All of the software is current.Results:
OK - All of the software is current. Proceed to Test Step 2.
NOT OK - There is a more recent software release that is available.Repair: Flash all controls with the latest software release. Refer to Testing and Adjusting, KENR8292, "Electronic Control Unit - Flash Program".STOPTest Step 2. VERIFY THAT THE SHIFTER IS PRESENT.
Verify that the ECU recognizes the shifter.Expected Result:The ECU recognizes the installation of the shifter.Results:
OK - The ECU recognizes the installation of the shifter.Repair: The shifter may have failed. Replace the shifter. Proceed to Test Step 3.
NOT OK - The ECU does not recognize the installation of the shifter. Remove the shifter and then install the shifter. Proceed to Test Step 3.Test Step 3. VERIFY THAT THE DIAGNOSTIC CODE IS PRESENT.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all of the harness connectors. Make sure that the connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 2990 FMI 12 is active.Expected Result:
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
D10N, D8L, D9N
D11N
D11N, D11R, D11T
D10, D11N, D11R, D11T
D11N, D11R
D11N, D11R, D11T
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
D10N, D10R, D8L, D9L, D9N, D9R
D10N
D10N, D10R
789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, D6H, D6H XL, D6H XR, D6R
5130, 5130B, 560B, 580, 580B, 776C, 777D, 777F, 777G, 844, 844H, 950H, 990, 990 II, 990H, CB-434B, CB-434C, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D...
931B, D3B, D6H, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
3T5224
SEAL-SPOOL
933C, 939C, AP-200B, D3C III, D4C III, D5B, D5C III, D5E, D6H, D6H XL, D6H XR, D6R, D7H, D7R XR
933C, 939C, AP-200B, D3C III, D4C III, D5B, D5C III, D5E, D6H, D6H XL, D6H XR, D6R, D7H, D7R XR
7X1552
SEAL-V-RING
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
572R, D6H, D6H II, D6H XL, D6H XR, D6R, D7R
3T7135
SEAL
D6H, D6H XL, D6H XR, D7H, D8N, D8R
D6H, D6H XL, D6H XR, D7H, D8N, D8R
3T6281
SEAL
D10N, D10R, D11N, D11R, D6H, D6H XL, D6H XR, D7H, D8L, D8N, D8R, D9L, D9N, D9R
D10N, D10R, D11N, D11R, D6H, D6H XL, D6H XR, D7H, D8L, D8N, D8R, D9L, D9N, D9R
3T7115
SEAL
D6H, D6H XL, D6H XR, D7H, D8N
D6H, D6H XL, D6H XR, D7H, D8N
9G1240
SEAL
D10, D11N, D6H, D6H II, D6H XL, D6H XR, D7H, D8L, D8N, D9L
D10, D11N, D6H, D6H II, D6H XL, D6H XR, D7H, D8L, D8N, D9L
8E1419
SEAL
D11N, D6H, D7H
D11N, D6H, D7H
330B L, 330C L, 345B II, 916, 926, 936, 936F, 950K, 962K, 966K, 972K, 980K, CS-643, D10, D5H, D6H, D7H, D8L, D9L, G936, IT28