6V9397 SEAL Caterpillar parts
321B, 325C, 950G II
Rating:
Alternative (cross code) number:
CA6V9397
6V-9397
6V9397
CA6V9397
6V-9397
6V9397
Weight: 0.05 pounds 0 kg.
EXCAVATOR, WHEEL LOADER,
Number on catalog scheme:
13
For full view, you need register
Information:
Screed Lift Cylinder
Illustration 1 g03388846
Left Side of Machine (1) Screed lift cylinderEach side of the machine is equipped with screed lift cylinder (1). The left screed lift cylinder is shown.Pressurized oil is directed into screed lift cylinders (1) under the following conditions: the screed is lifted, or the screed assist system is operating. The head ends of the screed lift cylinders are always open to the hydraulic tank. When the screed is being lowered, the rod ends of the screed lift cylinders are also open to the hydraulic tank. In this case, gravity forces the screed to the ground. The inlet port at the rod end of each screed lift cylinder contains an orifice. The orifice limits the rate at which the screed will lower. Tow Point Cylinder
Illustration 2 g03388847
Right Side of Machine (2) Tow point cylinderEach side of the machine is equipped with tow point cylinder (2). The right tow point cylinder is shown.Each tow point cylinder (2) raises and lowers the respective tow point of each cylinder. When the tow point is changed, the angle of attack of the screed is changed. The tow point solenoids on the tow point manifold control the oil which flows to the tow point cylinders. When oil is directed into the head end of the tow point cylinder, the tow point lowers and the angle of attack decreases. When oil is directed into the rod end of the tow point cylinder, the tow point rises, and the angle of attack increases.Hopper Cylinder
Illustration 3 g03388848
Left Side of Machine (3) Hopper cylinderEach side of the hopper is equipped with hopper cylinder (3). The left hopper cylinder is shown.Hopper cylinders (3) open and close the hopper wings. The hopper solenoids on the auxiliary manifold control the oil flow to the hopper cylinders. When oil is directed into the rod ends of the hopper cylinders, the hopper wings open. When oil is directed into the head ends of the hopper cylinders, the hopper wings close.Steering Cylinder
Illustration 4 g03388849
Under Hopper (4) Steering cylinder (5) Main tie rod (6) Linking tie rodSteering cylinder (4) is located under the hopper, between the front set of tandem steering wheels. The steering cylinder is connected to the front set of steering wheels and the rear set of steering wheels by tie rods.The head end of steering cylinder (4) is connected to the machine frame. The rod end of the steering cylinder is connected to main tie rod (5). This tie rod is connected to the front set of steering wheels.The front wheels and the rear wheels on each side of the machine are connected by linking tie rod (6). This tie rod ensures the wheels turn in tandem. The mechanical linkages between the wheel sets allow the front and rear wheels to pivot at different rates.The metering pump directs the oil which flows to steering cylinder (4). When
Illustration 1 g03388846
Left Side of Machine (1) Screed lift cylinderEach side of the machine is equipped with screed lift cylinder (1). The left screed lift cylinder is shown.Pressurized oil is directed into screed lift cylinders (1) under the following conditions: the screed is lifted, or the screed assist system is operating. The head ends of the screed lift cylinders are always open to the hydraulic tank. When the screed is being lowered, the rod ends of the screed lift cylinders are also open to the hydraulic tank. In this case, gravity forces the screed to the ground. The inlet port at the rod end of each screed lift cylinder contains an orifice. The orifice limits the rate at which the screed will lower. Tow Point Cylinder
Illustration 2 g03388847
Right Side of Machine (2) Tow point cylinderEach side of the machine is equipped with tow point cylinder (2). The right tow point cylinder is shown.Each tow point cylinder (2) raises and lowers the respective tow point of each cylinder. When the tow point is changed, the angle of attack of the screed is changed. The tow point solenoids on the tow point manifold control the oil which flows to the tow point cylinders. When oil is directed into the head end of the tow point cylinder, the tow point lowers and the angle of attack decreases. When oil is directed into the rod end of the tow point cylinder, the tow point rises, and the angle of attack increases.Hopper Cylinder
Illustration 3 g03388848
Left Side of Machine (3) Hopper cylinderEach side of the hopper is equipped with hopper cylinder (3). The left hopper cylinder is shown.Hopper cylinders (3) open and close the hopper wings. The hopper solenoids on the auxiliary manifold control the oil flow to the hopper cylinders. When oil is directed into the rod ends of the hopper cylinders, the hopper wings open. When oil is directed into the head ends of the hopper cylinders, the hopper wings close.Steering Cylinder
Illustration 4 g03388849
Under Hopper (4) Steering cylinder (5) Main tie rod (6) Linking tie rodSteering cylinder (4) is located under the hopper, between the front set of tandem steering wheels. The steering cylinder is connected to the front set of steering wheels and the rear set of steering wheels by tie rods.The head end of steering cylinder (4) is connected to the machine frame. The rod end of the steering cylinder is connected to main tie rod (5). This tie rod is connected to the front set of steering wheels.The front wheels and the rear wheels on each side of the machine are connected by linking tie rod (6). This tie rod ensures the wheels turn in tandem. The mechanical linkages between the wheel sets allow the front and rear wheels to pivot at different rates.The metering pump directs the oil which flows to steering cylinder (4). When
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2, 320D2 L, 322C, 323D L, 323D2 L, 324D, 324D L, 325C, 325D L, 329D, 329D L
320C, 320D, 321B, 321C, 321D LCR, 322C, 324D, 324D L, 325C, 325C L, 328D LCR, 330C L
320C, 320D, 320D L, 320E L, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L, 330C L
1390, 2590, 325B L, 325C, 325C L, 325D L, 325D MH, 330B L, 330C L, 330D, 330D L, 336D, 345B, 345B II, 345B II MH, 385B, 541, 541 2, 551, 552, 552 2, M325B, TK1051, TK741, TK751, TK752, W330B, W345B II
322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336...
322B, 324D, 324D L, 325B, 325C, 325D L, 326D L, 329D, 329D L, 330B, 330B L, 330C L, 330D, 330D L, 336D, 336D L, 336D2
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325B, 325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 325C L, 325D, 325D L, 328D LCR, 329D, 329D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
325C, 330C L, 330D L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345C, 345D, 345D L, 349D, 349D L
3K3060
SEAL
950G II
950G II
2588600
SEAL
980H
980H
7X1550
SEAL
966H
966H
2442126
SEAL
950H
950H
2K0360
SEAL
325C, 330B, 966H
325C, 330B, 966H
6D8397
SEAL
966G II
966G II
3Y6668
SEAL
950, 966C
950, 966C
3Y6666
SEAL
950, 966C
950, 966C
3Y6667
SEAL
950, 966C
950, 966C
3J0524
SEAL
966H
966H
6B8398
SEAL
966H
966H