7I2329 SEAL Caterpillar parts
307, 307B, E70B
Rating:
Alternative (cross code) number:
CA7I2329
7I-2329
7I2329
CA7I2329
7I-2329
7I2329
Weight: 0.09 pounds 0 kg.
EXCAVATOR, MINI HYD EXCAVATOR,
Number on catalog scheme:
5
For full view, you need register
Information:
Installation Procedure
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02173073
If necessary, follow Step 2.a through Step 2.d in order to install bracket (29).
Position bracket (29) onto cylinder head (30).
Install bolts (28) hand tight. Ensure that rubber sleeve (32) is correctly positioned into recess of bracket (29).
Tighten bolts (28) to a torque of 22 N m (195 lb in).
Install new cable straps (31). Note: Ensure that the cable straps meet Original Equipment Manufacturers (OEM) specification.
Illustration 2 g02169940
Illustration 3 g02169941
Position a new gasket (15) onto inlet air control assembly (6). Ensure gasket (15) is correctly installed into locating Pins (A).
Loosen bolts (34) for bracket (33).
Illustration 4 g02169794
Illustration 5 g02351557
Illustration 6 g02169941
Position inlet air control assembly (6) onto bracket. Note: Ensure that the inlet air control assembly is correctly installed onto hose assembly for the inlet elbow.
Install bolts (25) and bolts (14) hand tight.
Tighten bolts (25) to a torque of 22 N m (195 lb in).
Tighten bolts (14) to a torque of 22 N m (195 lb in).
Tighten bolts (34) for bracket (33) to a torque of 44 N m (32 lb ft).
Connect temperature sensor (16) to the inlet air control assembly. Refer to Disassembly and Assembly, "Temperature Sensor (Cooled Exhaust Gas) - Remove and Install" for the correct procedure.
Install a new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) to tube assembly (23).
Position tube assembly (23) onto inlet air control assembly (6). Install install remaining new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) finger tight.
Install bolt (17) (not shown) and bolt (25) to clips for tube assembly (23).
Tighten banjo bolt (21) to a torque of 15 N m (133 lb in).
Tighten bolt (17) (not shown) and bolt (25) to a torque of 22 N m (195 lb in).
Install hose assembly onto turbocharger wastegate actuator and slide clip (19) along hose assembly. Note: Ensure that clip for hose assembly is correctly positioned onto the hose assembly.
Position a new hose clamp (17) and a new hose clamp (19) onto hose
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02173073
If necessary, follow Step 2.a through Step 2.d in order to install bracket (29).
Position bracket (29) onto cylinder head (30).
Install bolts (28) hand tight. Ensure that rubber sleeve (32) is correctly positioned into recess of bracket (29).
Tighten bolts (28) to a torque of 22 N m (195 lb in).
Install new cable straps (31). Note: Ensure that the cable straps meet Original Equipment Manufacturers (OEM) specification.
Illustration 2 g02169940
Illustration 3 g02169941
Position a new gasket (15) onto inlet air control assembly (6). Ensure gasket (15) is correctly installed into locating Pins (A).
Loosen bolts (34) for bracket (33).
Illustration 4 g02169794
Illustration 5 g02351557
Illustration 6 g02169941
Position inlet air control assembly (6) onto bracket. Note: Ensure that the inlet air control assembly is correctly installed onto hose assembly for the inlet elbow.
Install bolts (25) and bolts (14) hand tight.
Tighten bolts (25) to a torque of 22 N m (195 lb in).
Tighten bolts (14) to a torque of 22 N m (195 lb in).
Tighten bolts (34) for bracket (33) to a torque of 44 N m (32 lb ft).
Connect temperature sensor (16) to the inlet air control assembly. Refer to Disassembly and Assembly, "Temperature Sensor (Cooled Exhaust Gas) - Remove and Install" for the correct procedure.
Install a new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) to tube assembly (23).
Position tube assembly (23) onto inlet air control assembly (6). Install install remaining new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) finger tight.
Install bolt (17) (not shown) and bolt (25) to clips for tube assembly (23).
Tighten banjo bolt (21) to a torque of 15 N m (133 lb in).
Tighten bolt (17) (not shown) and bolt (25) to a torque of 22 N m (195 lb in).
Install hose assembly onto turbocharger wastegate actuator and slide clip (19) along hose assembly. Note: Ensure that clip for hose assembly is correctly positioned onto the hose assembly.
Position a new hose clamp (17) and a new hose clamp (19) onto hose
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 143...
140, 141, 153, 163, 173B, 183B, 191, 206B, 212B, 215, 215B, 216, 216B, 216B3, 225, 226B, 226B3, 232B, 235, 235B, 235C, 235D, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 245, 245B, 245D, 246C, 247, 247B...
307B, 307C, 307D, 308C, 308D, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, ...
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 2384C, 2484C, 24M, 301.5, 301.6C, 302.5, 302.5C, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305...
307B, 307C, 308C, 311, 311B, 312, 312B, 312B L, 313B, 315, 317, E110, E120B, E140, M315
307, 307B, 307C, 307D, 308C, 308D, 308E CR, 308E2 CR, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E ...
2384C, 2484C, 301.5, 304, 304C CR, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 3...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 305.5D, 305.5E, 305C CR, 307, 307B, 307C, 308C, 308D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 303, 303.5, 303.5C, 304, 304.5, 305, 305.5, 305.5E, 306, 306E, 307, 307B, 307D, 308D, 311, 311D LRR, 312, 314D CR, 314D LCR,...
307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 312C L, 324D L, 325D MH, 330D, 330D L, 330D MH, 345C, 345C MH, E110, E120B, E180, E240, E70, E70B, EL240, M325D L MH, M325D M...
304.5, 305.5D, 305.5E, 307, 307B, 902, 906, E70, E70B
307, 311C, 313B, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 3...
0966789
SEAL
307, 307B, 307C, 308C, E70, E70B
307, 307B, 307C, 308C, E70, E70B
184, 229D, 231D, 245, 245B, 24M, 320C, 320D FM, 515, 518C, 525, 528B, 530B, 543, 551, 552, 552 2, 613C, 613C II, 613G, 621, 621B, 621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, ...
572R, 572R II, 777F, 777G, 834B, 988F II, 993K, D7E, D7E LGP, M312, M315, M318, M320
1151542
SEAL-SHAFT
143H, 163H, 163H NA, 533, 543, 564, 572R, 572R II, 574B, 953C, D6R II, HA770, HA771, HA870, HA871, M312, TK370, TK371, TK380, TK381
143H, 163H, 163H NA, 533, 543, 564, 572R, 572R II, 574B, 953C, D6R II, HA770, HA771, HA870, HA871, M312, TK370, TK371, TK380, TK381
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320N, 322 FM L, 322 LN, 322B L, 32...
307, 307B, 307C, 307D, 308C, 308D, 324D L, 325D MH, 330D, 330D L, 330D MH, 345C, 345C MH, E70B, M312, M313C, M313D, M315D 2, M317D 2, M325D L MH, M325D MH, M330D
307, 307B, 307C, 307D, 307E, 308C, E70, PM-465
4I9280
SEAL
307, 307B, 307C, 307D, 307E, 308E, E70B
307, 307B, 307C, 307D, 307E, 308E, E70B
307, 307B, 307C, 308C, E70, E70B
303, 303.5, 304.5, 307, 307B, 307D, E110, E120, E140, E300, E70, E70B
307, 307B, E70, E70B
307, 307B, 307C, 308C, 320C, 320D L, 320D LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325, 325 L, 325 LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L,...