7J9256 SEAL (standard) Caterpillar parts
235, 235C, 245
Rating:
Alternative (cross code) number:
CA7J9256
7J-9256
7J9256
CA7J9256
7J-9256
7J9256
Weight: 0.30 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
19
For full view, you need register
7J9256
Images:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
B - Loctite 5900 Flange Sealant 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
Illustration 1 g01149000
Remove tube assembly (1).
Illustration 2 g01149001
Disconnect hose assemblies (3).
Remove engine oil pan (2) and the gasket.
Illustration 3 g01149003
Disconnect tube assembly (4) from engine oil pan (5).
Use Tooling (A) to support engine oil pan (5). The weight of engine oil pan (5) is approximately 105 kg (235 lb).
Remove bolts (6). Remove engine oil pan (5) and the gasket.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install engine oil pan (7) in reverse order of removal.
Apply Tooling (B) on the four socket joints of the oil pan gasket and the four T-joints on the bottom of the block where the front and rear housings meet the block.
Illustration 4 g02226333
Tightening Sequence
The directional arrow is towards the front housing of the engine.
Tighten bolts (6) in sequence to a torque of 47 9 N m (35 7 lb ft).
Tighten bolts (6) again in sequence to a torque of 47 9 N m (35 7 lb ft).
If the oil drain plug was removed, install the oil drain plug. Tighten the oil drain plug to a torque of 70 10 N m (52 7 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
B - Loctite 5900 Flange Sealant 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
Illustration 1 g01149000
Remove tube assembly (1).
Illustration 2 g01149001
Disconnect hose assemblies (3).
Remove engine oil pan (2) and the gasket.
Illustration 3 g01149003
Disconnect tube assembly (4) from engine oil pan (5).
Use Tooling (A) to support engine oil pan (5). The weight of engine oil pan (5) is approximately 105 kg (235 lb).
Remove bolts (6). Remove engine oil pan (5) and the gasket.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install engine oil pan (7) in reverse order of removal.
Apply Tooling (B) on the four socket joints of the oil pan gasket and the four T-joints on the bottom of the block where the front and rear housings meet the block.
Illustration 4 g02226333
Tightening Sequence
The directional arrow is towards the front housing of the engine.
Tighten bolts (6) in sequence to a torque of 47 9 N m (35 7 lb ft).
Tighten bolts (6) again in sequence to a torque of 47 9 N m (35 7 lb ft).
If the oil drain plug was removed, install the oil drain plug. Tighten the oil drain plug to a torque of 70 10 N m (52 7 lb ft).
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
235, 235C, 245, 245B, 5230, 651E, 657E, 657G, 966H, 972H, 980G, 980G II, 980H, 988B, 988F, 988F II, 994, 994D, 994F, 994H, D11N, D11R, D11T
235, 235C, 245B
235, 235C, 245, 245B, 365B, 365B II, 365C, 365C L, 385B, 385C L, 5230, 5230B, 980G, 980G II, 980H, D11N, D11R, D11T
231D, 235B, 235C, 235D, 330B L, 330C FM, 330D FM, 568 FM LL, 836, 963, 963B, 963C, 973, D5H XL, D5R LGP, D6H, D6H XL, D6H XR, D6N, D6N LGP, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7H, D7...
235C, 235D
235C, 235D
235C, 235D, 245, 245B, 245D, 988K, 990, 990 II
245, 245B, 990, 990 II
235, 235C
235, 235C, 24H, 24M
235C, 245, 245B, 5230, D8N, D8R, D8R II, D8T
120M, 120M 2, 12M 2, 12M 3 AWD, 140M, 140M 2, 140M 3 AWD, 160M, 160M 2, 160M 3 AWD, 235C, 235D, 245B, 533, 539, 543, 554, 564, 572R, 574, 574B, 623H, D6H, D6H XL, D6H XR, D6R, D7H, D7R, D8N, HA770, HA...
235, 245, 988G
235, 245, 5230, 657B, 657E
215, 235, 621, 621B, 621E, 627B, 627E, 773B, 936, 963, 973, 977K, 977L, 980, G936
225, 227, 229, 229D, 231D, 235, 235B, 235C
127, 172, 183, 184, 225, 227, 229, 235, 235B, 24, 25, 46, 910, 918F, 924F, IT18F, IT24F, PR-450C
4S8391
SEAL 76 in.
120, 12F, 12G, 140, 14E, 225, 768B, 769, 824B, 826B, 834, 950, 966C, 980B, 988, D5
120, 12F, 12G, 140, 14E, 225, 768B, 769, 824B, 826B, 834, 950, 966C, 980B, 988, D5
235
235, 235C, 245
235, 235B, 235C, 245, 245D
235, 235B, 235C, 235D, 245, 245B, 245D
235, 235B, 235C, 245