7X2793 SEAL KIT- Caterpillar parts
Rating:
Alternative (cross code) number:
CA7X2793
7X-2793
7X2793
CA7X2793
7X-2793
7X2793
Weight: 1 pounds 0 kg.
For full view, you need register
Information:
Installation Procedure
Note: Make sure that all mounting surfaces are clean prior to installation.
Illustration 1 g00304904
Typical Example
Fasten a suitable retainer around the axle, around front axle support (5) and around yoke (6). This will prevent the front axle support and the yoke from falling as the oscillating axle is being installed.
Illustration 2 g00292098
Fasten a suitable lifting sling to each side of the oscillating axle, as shown. Fasten a hoist to both lifting slings. Raise the oscillating axle into position. The weight of the oscillating axle is 1225 kg (2700 lb).
Illustration 3 g00292102
Install nuts (4) that hold front axle support (5) to the machine frame. The torque for nuts (4) is 475 60 N m (350 45 lb ft).
Illustration 4 g00292100
Install nuts (4) that hold rear axle support (3) to the machine frame. The torque for nuts (4) is 475 60 N m (350 45 lb ft).
Connect tube assembly (2) to rear axle support (3). Also connect the tube assembly to the front axle support.
Illustration 5 g00304903
Connect hose assembly (1) to the oscillating axle.
Fill the oscillating axle. The capacity of the oscillating axle is 36 L (10 US gal). Refer to Operation and Maintenance Manual, SEBU7018 for the correct procedure.
Lubricate the front supports and the rear supports. Refer to Operation and Maintenance Manual, SEBU7018 for the correct procedure., End By:
Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) - Remove and Install".
Install the rear tires and the rims. Refer to Disassembly and Assembly, "Tire and Rim (Rear) - Remove and Install".
Purge the air from the braking system. Refer to Testing and AdjustingSENR1387, "950G Wheel Loader and 962G Wheel Loader Braking System" for the correct procedure.
Note: Make sure that all mounting surfaces are clean prior to installation.
Illustration 1 g00304904
Typical Example
Fasten a suitable retainer around the axle, around front axle support (5) and around yoke (6). This will prevent the front axle support and the yoke from falling as the oscillating axle is being installed.
Illustration 2 g00292098
Fasten a suitable lifting sling to each side of the oscillating axle, as shown. Fasten a hoist to both lifting slings. Raise the oscillating axle into position. The weight of the oscillating axle is 1225 kg (2700 lb).
Illustration 3 g00292102
Install nuts (4) that hold front axle support (5) to the machine frame. The torque for nuts (4) is 475 60 N m (350 45 lb ft).
Illustration 4 g00292100
Install nuts (4) that hold rear axle support (3) to the machine frame. The torque for nuts (4) is 475 60 N m (350 45 lb ft).
Connect tube assembly (2) to rear axle support (3). Also connect the tube assembly to the front axle support.
Illustration 5 g00304903
Connect hose assembly (1) to the oscillating axle.
Fill the oscillating axle. The capacity of the oscillating axle is 36 L (10 US gal). Refer to Operation and Maintenance Manual, SEBU7018 for the correct procedure.
Lubricate the front supports and the rear supports. Refer to Operation and Maintenance Manual, SEBU7018 for the correct procedure., End By:
Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) - Remove and Install".
Install the rear tires and the rims. Refer to Disassembly and Assembly, "Tire and Rim (Rear) - Remove and Install".
Purge the air from the braking system. Refer to Testing and AdjustingSENR1387, "950G Wheel Loader and 962G Wheel Loader Braking System" for the correct procedure.
Parts seal Caterpillar catalog:
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar