7Y4629 SEAL-U-CUP Caterpillar parts
318B, 320 L, 320B, 325, 325 L, 325 LN, 325B L, 330B L, 345B L
Rating:
Alternative (cross code) number:
CA7Y4629
7Y-4629
7Y4629
CA7Y4629
7Y-4629
7Y4629
Weight: 0.06 pounds 0 kg.
EXCAVATOR,
Cross Reference:
CATERPILLAR
7Y4629,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$10.84
07 May 2022
1.0[0.45] Pounds
US: ProperBuy
2160004 Seal-U-Cup Fits Caterpillar 7Y4629 319C 319D 319D L 319D LN 320B 320B L
TCP Warranty
TCP Warranty
Number on catalog scheme:
18
For full view, you need register
Compatible equipment models: 7Y4629:
Information:
Prelube Test
Turn the Engine Control Switch to the LOCAL position.
Turn the Prelube/Start Switch to the PRELUBE position.
The "PRELUBE" light should illuminate.
The engine should start.Test for the Local Emergency Stop
Start the engine.
Push the "E-Stop" button on the control panel.
The engine should shut down.
Release the "E-Stop". Turn the Engine Control Switch to the OFF/RESET position. The shutdown relay should de-energize.
Manually reset the air shutoff.
The engine should start.Test for the Remote Emergency Stop
Start the engine.
Push the "E-Stop" button at the remote location.
The engine should shut down.
Release the "E-Stop". Turn the Engine Control Switch to the OFF/RESET position. The shutdown relay should de-energize.
Manually reset the air shutoff.
The engine should start.Test for Shutdowns
The test will check all of the shutdowns in order to ensure that the engine will shut off when a shutdown is active.The following procedure will simulate the shutdowns for the system. The engine should shut off for each shutdown.
Start the engine.
Run the engine at a RPM that is greater than the RPM of the oil step.Note: A signal generator can be used in order to simulate a running engine. See Testing and Adjusting, RENR5851, "Setpoint - Check" for more information.
Jumper the terminals in Table 1 for one of the shutdowns that has not been tested.The engine should shut down.Note: If the system is equipped with an annunciator, check the indicator for the active shutdown. The indicator should be illuminated.
After the engine shuts down, place the engine control switch in the OFF/RESET position.
If the system is equipped with an annunciator, actuate the acknowledged switch and depress the reset push button.
Manually reset the air shutoff.
Place the engine control switch in the LOCAL position.
Restart from Step 1 until all of the shutdowns have been tested.
Table 1
Short the Listed Terminals in order to Simulate the Shutdown.
Shutdown Terminals Tested (3)
Overspeed (1) N/A
High crankcase pressure 11, 90
Low engine oil pressure (low speed) 12, 91
Low engine oil pressure (high speed) 14, 93
Metal particle detector 32, 90
High engine oil temperature (2) 18, 90
High jacket water coolant temperature (2) 15, 91
Loss of jacket water (2) 2, 66
Customer option 1A, 41
( 3 ) Place a check after the test when the test is completed.
( 1 ) See Testing and Adjusting, "Overspeed Verification Test".
( 2 ) The shutdown is not used on minimal systems.Test for Alarms
The test will check all of the alarms in order to ensure that the alarm circuit will energize. The following procedure will simulate the alarms for the system.
Start the engine.
Run the engine at a RPM that is greater than the RPM of the oil step.Note: A signal generator can be used in order to simulate a running engine. See Testing and Adjusting, RENR5851, "Setpoint - Check" for more information.
Jumper the terminals in Table
Turn the Engine Control Switch to the LOCAL position.
Turn the Prelube/Start Switch to the PRELUBE position.
The "PRELUBE" light should illuminate.
The engine should start.Test for the Local Emergency Stop
Start the engine.
Push the "E-Stop" button on the control panel.
The engine should shut down.
Release the "E-Stop". Turn the Engine Control Switch to the OFF/RESET position. The shutdown relay should de-energize.
Manually reset the air shutoff.
The engine should start.Test for the Remote Emergency Stop
Start the engine.
Push the "E-Stop" button at the remote location.
The engine should shut down.
Release the "E-Stop". Turn the Engine Control Switch to the OFF/RESET position. The shutdown relay should de-energize.
Manually reset the air shutoff.
The engine should start.Test for Shutdowns
The test will check all of the shutdowns in order to ensure that the engine will shut off when a shutdown is active.The following procedure will simulate the shutdowns for the system. The engine should shut off for each shutdown.
Start the engine.
Run the engine at a RPM that is greater than the RPM of the oil step.Note: A signal generator can be used in order to simulate a running engine. See Testing and Adjusting, RENR5851, "Setpoint - Check" for more information.
Jumper the terminals in Table 1 for one of the shutdowns that has not been tested.The engine should shut down.Note: If the system is equipped with an annunciator, check the indicator for the active shutdown. The indicator should be illuminated.
After the engine shuts down, place the engine control switch in the OFF/RESET position.
If the system is equipped with an annunciator, actuate the acknowledged switch and depress the reset push button.
Manually reset the air shutoff.
Place the engine control switch in the LOCAL position.
Restart from Step 1 until all of the shutdowns have been tested.
Table 1
Short the Listed Terminals in order to Simulate the Shutdown.
Shutdown Terminals Tested (3)
Overspeed (1) N/A
High crankcase pressure 11, 90
Low engine oil pressure (low speed) 12, 91
Low engine oil pressure (high speed) 14, 93
Metal particle detector 32, 90
High engine oil temperature (2) 18, 90
High jacket water coolant temperature (2) 15, 91
Loss of jacket water (2) 2, 66
Customer option 1A, 41
( 3 ) Place a check after the test when the test is completed.
( 1 ) See Testing and Adjusting, "Overspeed Verification Test".
( 2 ) The shutdown is not used on minimal systems.Test for Alarms
The test will check all of the alarms in order to ensure that the alarm circuit will energize. The following procedure will simulate the alarms for the system.
Start the engine.
Run the engine at a RPM that is greater than the RPM of the oil step.Note: A signal generator can be used in order to simulate a running engine. See Testing and Adjusting, RENR5851, "Setpoint - Check" for more information.
Jumper the terminals in Table
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
320 L, 320B, 320N, 322B, 322B LN, 325, 325 L, 325 LN, 325B L, 325C FM, 325D FM, 325D FM LL, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330C L, 345B II, 345B L, M325B
320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C, 321D LCR, 322...
320 L, 320B, 320B L, 320N, 321B, 345B, 345B L, OEMS
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
320B, 325 L, 325B L, OEMS
320 L, 325 L
330, 330B, 330B L, OEMS
330, 330 L, 345B, 345B II, 345B L, 350, OEMS
330C, 330D L, 330D MH, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
330, 330 FM L, 330 L, 330B, 330B L, E120B, W330B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK711, TK721, TK722, TK732, TK741, TK751, TK752
1090, 1190, 1190T, 1390, 2290, 2390, 2391, 315B FM L, 315C, 315D L, 317B LN, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320...
301.6C, 308E, 308E CR, 308E SR, 308E2 CR, 312C, 313D2 LGP, 315B FM L, 315C, 315D L, 316E L, 317B LN, 318B, 318C, 318D L, 318D2 L, 319C, 320 L, 320B, 320B L, 320C, 320C L, 320E, 320E LRR, 320E RR, 320N...
120G, 120K, 120K 2, 12G, 12K, 130G, 140G, 140K, 140K 2, 14G, 14H, 14H NA, 160G, 160K, 16G, 16H, 16H NA, 315C, 315D L, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C ...
303.5C, 304D CR, 305C CR, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
303.5C, 304D CR, 305C CR, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
312, 318B, 320, 320B, 320C, 322 FM L, 322 LN, 322B L, 322C, 322C FM, 325, 325B L, 345B L, 5080, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, EL240B
318B, 320C, 322B L, 322C, 322C FM, 325B L, 5080
1874803
SEAL-O-RING
318B
318B
2127963
SEAL
318B
318B
2127964
SEAL
318B
318B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, ...