8C3081 SEAL-O-RING Caterpillar parts
216B, 216B3, 226B, 226B3, 242B3, 242D, 246C, 247B, 247B3, 252B, 252B3, 256C, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 29...
Rating:
Alternative (cross code) number:
CA8C3081
8C-3081
8C3081
CA8C3081
8C-3081
8C3081
Weight: 30 pounds 13 kg.
Information:
CROSS SECTION DIAMETER
2.62
mm
DASH SIZE
144
ID
63.17
mm
MATERIAL
Nitrile (NBR) Rubber - 75 Duro
OD
0
mm
CHALLENGER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 8C3081:
MINI HYD EXCAVATOR
304.5
Information:
Use this procedure to troubleshoot a high dosing air assist pressure. Also, use this procedure if the following event code is active or logged.
Table 1
J1939 Code and Description Comments
4335-15
Aftertreatment #1 SCR Dosing Air Assist Absolute Pressure : High - least severe (1) The air pressure is above the trip point for the programmed delay time.
Dosing is disabled until the pressure is correct.
The code is logged.
Table 2
Associated Codes
J1939 Code CDL Code Troubleshooting Procedure
4335-3 3092-3 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4335-4 3092-4 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4336-5 3094-5 Troubleshooting, "Solenoid Valve - Test"
4336-6 3094-6 Troubleshooting, "Solenoid Valve - Test" Probable Causes
Codes
Air pressureRecommended Actions
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Turn the DC breaker, located in the power distribution box, to the ON position.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Air Supply to the Dosing Cabinet
A. Turn the DC breaker, located in the power distribution box, to the OFF position.
B. Disconnect the air supply line to the dosing cabinet.
C. Install a pressure gauge on the air supply line to the dosing cabinet.
D. Monitor the air supply pressure from the air compressor.
E. Reconnect the air supply line to the dosing cabinet.
483 kPa to 1068 kPa (70 psi to 155 psi)
Result: The air supply pressure from the air compressor is 483 kPa to 1068 kPa (70 psi to 155 psi).
Proceed to Test Step 4.
Result: The air supply pressure from the air compressor is greater than 1068 kPa (155 psi).
Repair: There is a problem with the air supply to the dosing cabinet. For information on the air compressor, refer to the Original Equipment Manufacturers (OEM) service information.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Air Pressure
A. Turn the DC breaker, located in the power distribution box, to the ON position.
B. Connect Cat ET.
C.
Table 1
J1939 Code and Description Comments
4335-15
Aftertreatment #1 SCR Dosing Air Assist Absolute Pressure : High - least severe (1) The air pressure is above the trip point for the programmed delay time.
Dosing is disabled until the pressure is correct.
The code is logged.
Table 2
Associated Codes
J1939 Code CDL Code Troubleshooting Procedure
4335-3 3092-3 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4335-4 3092-4 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4336-5 3094-5 Troubleshooting, "Solenoid Valve - Test"
4336-6 3094-6 Troubleshooting, "Solenoid Valve - Test" Probable Causes
Codes
Air pressureRecommended Actions
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Turn the DC breaker, located in the power distribution box, to the ON position.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Air Supply to the Dosing Cabinet
A. Turn the DC breaker, located in the power distribution box, to the OFF position.
B. Disconnect the air supply line to the dosing cabinet.
C. Install a pressure gauge on the air supply line to the dosing cabinet.
D. Monitor the air supply pressure from the air compressor.
E. Reconnect the air supply line to the dosing cabinet.
483 kPa to 1068 kPa (70 psi to 155 psi)
Result: The air supply pressure from the air compressor is 483 kPa to 1068 kPa (70 psi to 155 psi).
Proceed to Test Step 4.
Result: The air supply pressure from the air compressor is greater than 1068 kPa (155 psi).
Repair: There is a problem with the air supply to the dosing cabinet. For information on the air compressor, refer to the Original Equipment Manufacturers (OEM) service information.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Air Pressure
A. Turn the DC breaker, located in the power distribution box, to the ON position.
B. Connect Cat ET.
C.
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
1155658
SEAL
834B, 844, 844H, 844K, 854G, 854K, 988B, 988F, 990, 990 II, 990H, 990K, 992G, 992K, R2900, R2900G, R3000H
834B, 844, 844H, 844K, 854G, 854K, 988B, 988F, 990, 990 II, 990H, 990K, 992G, 992K, R2900, R2900G, R3000H
9U1742
SEAL-O-RING
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
1463644
SEAL AS
950F, 950F II, 950G, 960F, 962G
950F, 950F II, 950G, 960F, 962G
8T1797
SEAL AS
988K, 990, 990 II, 990H, 990K, 992C, 992D, R3000H
988K, 990, 990 II, 990H, 990K, 992C, 992D, R3000H
5P9609
SEAL-LIP TYPE
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, D11N, D11R, D11T
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, D11N, D11R, D11T
9X7546
SEAL-LIP TYPE
528, 528B, 530B, 533, 543, 816B, 950F, 950F II, 960F, 966C, 966F, 966F II, 970F, HA770, HA771, HA870, HA871, R1600, R1600G, R1600H, TK370, TK371, TK380, TK381
528, 528B, 530B, 533, 543, 816B, 950F, 950F II, 960F, 966C, 966F, 966F II, 970F, HA770, HA771, HA870, HA871, R1600, R1600G, R1600H, TK370, TK371, TK380, TK381
4K7462
SEAL-LIP TYPE
14G, 14H, 14H NA, 14M, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 824K, 825K, 826K, 966C, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 97...
14G, 14H, 14H NA, 14M, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 824K, 825K, 826K, 966C, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 97...
4K7461
SEAL-LIP TYPE
14G, 14H, 14H NA, 14M, 16, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 966C, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K
14G, 14H, 14H NA, 14M, 16, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 966C, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K
1241859
SEAL-O-RING
5110B, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844, 988B, 988F, 988F II, 990, 990 II
5110B, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844, 988B, 988F, 988F II, 990, 990 II
7X1548
SEAL
14M, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
14M, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
1456033
SEAL GP-DUO-CONE
784B, 793B, 793C, 990, 990 II
784B, 793B, 793C, 990, 990 II
0536950
SEAL
24H, AP-800C, AP-800D, BG-225B, CB-224C, CB-334D, CB-335D, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CB-634C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, ...
24H, AP-800C, AP-800D, BG-225B, CB-224C, CB-334D, CB-335D, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CB-634C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, ...
8T6850
SEAL-O-RING
120M 2, 307B, 345B II, 35, 45, 525D, 535D, 545D, 55, 554, 623E, 623F, 725, 730, 735, 740, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 924G, 924GZ, 933, 933C, 938G II...
120M 2, 307B, 345B II, 35, 45, 525D, 535D, 545D, 55, 554, 623E, 623F, 725, 730, 735, 740, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 924G, 924GZ, 933, 933C, 938G II...
5H8853
SEAL-O-RING
315D L, 35, 432D, 432E, 434E, 442D, 442E, 444E, 45, 527, 545, 55, 554, 561M, 570B, 572R, 572R II, 578, 580B, 583T, 587R, 587T, 589, 613C, 615, 615C, 777F, 793F, 793F CMD, 793F-XQ, 795F AC, 797F, 814B,...
315D L, 35, 432D, 432E, 434E, 442D, 442E, 444E, 45, 527, 545, 55, 554, 561M, 570B, 572R, 572R II, 578, 580B, 583T, 587R, 587T, 589, 613C, 615, 615C, 777F, 793F, 793F CMD, 793F-XQ, 795F AC, 797F, 814B,...
1165656
SEAL GP-DUO-CONE
45, 55
45, 55
1277415
SEAL
35, 45, 55
35, 45, 55
1244199
SEAL-O-RING
45, 55
45, 55
1285053
SEAL
35, 45, 55
35, 45, 55
1585999
SEAL-O-RING
35, 45, 55
35, 45, 55
1585998
SEAL-O-RING
35, 45, 55
35, 45, 55
1585104
SEAL-PISTON
35, 45, 55
35, 45, 55
1630429
SEAL-O-RING
35, 45, 55
35, 45, 55
0774035
SEAL-PISTON
35, 45, 55
35, 45, 55